Bedienungsanleitung Bosch GWS 750-100 I Professional (Seite 21 von 301) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

708228

Zoom out

Zoom in

Vorherige Seite

1/301

Nächste Seite

22 | English

1 609 92A 36R | (29.8.16) Bosch Power Tools

Switching On and Off

To start the power tool, push the On/Off switch 2 forwards.

To lock the On/Off switch 2, press the On/Off switch 2 down

at the front until it latches.

To switch off the power tool, release the On/Off switch 2 or,

if it is locked, briefly push down the back of the On/Off switch

2 and then release it.

 Check grinding tools before using. The grinding tool

must be mounted properly and be able to move freely.

Carry out a test run for at least one minute with no load.

Do not use damaged, out-of-centre or vibrating grind-

ing tools. Damaged grinding tools can burst and cause in-

juries.

To save energy, only switch the power tool on when using it.

Kickback stop (GWS 750-100 I)

In case of a sudden drop in speed, e.g.,

caused by a jammed disc while cutting, the

power supply to the motor is electronically

interrupted.

To restart the operation, switch the On/Off

switch 2 to the Off position and start the ma-

chine again.

Restarting Protection (GWS 700/GWS 710(115)/

GWS 750/GWS 750-100 I)

The restarting protection feature prevents uncontrolled re-

starting of the machine after an interruption in the power sup-

ply.

To restart the operation, switch the On/Off switch 2 to the

Off position and start the machine again.

Reduced starting current (GWS 750-100 I)

The electronic reduced starting current limits the power con-

sumption when switching the tool on and enables operation

from a 13 ampere fuse.

Working Advice

 Before any work on the machine itself, pull the mains

plug.

 Exercise caution when cutting slots in structural walls;

see Section “Information on Structures”.

 Clamp the workpiece if it does not remain stationary

due to its own weight.

 Do not strain the machine so heavily that it comes to a

standstill.

 After heavily straining the power tool, continue to run

it at no-load for several minutes to cool down the acces-

sory.

 Do not touch grinding and cutting discs before they

have cooled down. The discs can become very hot while

working.

 Do not use the power tool with a cut-off stand.

Rough Grinding

 Never use a cutting disc for roughing.

The best roughing results are achieved when setting the ma-

chine at an angle of 30° to 40°. Move the machine back and

forth with moderate pressure. In this manner, the workpiece

will not become too hot, does not discolour and no grooves

are formed.

Flap Disc

With the flap disc (accessory), curved surfaces and profiles

can be worked.

Flap discs have a considerably higher service life, lower noise

levels and lower sanding temperatures than conventional

sanding sheets.

Cutting Metal

 For cutting with bonded abrasives, always use the pro-

tection guard for cutting 14.

When cutting, work with moderate feed, adapted to the mate-

rial being cut. Do not exert pressure onto the cutting disc, tilt

or oscillate the machine.

Do not reduce the speed of running down cutting discs by ap-

plying sideward pressure.

The machine must al-

ways work in an up-

grinding motion. Other-

wise, the danger exists

of it being pushed un-

controlled out of the

cut.

When cutting profiles and square bar, it is best to start at the

smallest cross section.

Cutting Stone

 Provide for sufficient dust extraction when cutting

stone.

 Wear a dust respirator.

 The machine may be used only for dry cutting/grinding.

For cutting stone, it is best to use a diamond cutting disc.

For cutting especially hard material, e. g., concrete with high

pebble content, the diamond cutting disc can overheat and

become damaged as a result. This is clearly indicated by cir-

cular sparking, rotating with the diamond cutting disc.

In this case, interrupt the cutting process and allow the dia-

mond cutting disc to cool by running the machine for a short

time at maximum speed with no load.

Noticeably decreasing work progress and circular sparking

are indications of a diamond cutting disc that has become

dull. Briefly cutting into abrasive material (e.g. lime-sand

brick) can resharpen the disc again.

OBJ_BUCH-2565-002.book Page 22 Monday, August 29, 2016 2:42 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GWS 750-100 I Professional Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info