Bedienungsanleitung Bosch GWX 14-125 (Seite 22 von 347) (Alle Sprachen)

786305

Zoom out

Zoom in

Vorherige Seite

1/347

Nächste Seite

22 | English

Angle grinder GWX 10-125 GWX 14-125

Protection class / II / II

A) Rated no-load speed for the selection of appropriate application tools in accordance with ENIEC62841-2-3. The actual speed is lower for

safety reasons and according to production tolerances.

B) Depends on protective guard((8), (7), (11)) and auxiliary handle((5), (6)) in use

The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.

Noise/Vibration Information

Noise emission values determined according to

ENIEC62841-2-3.

Typically the A-weighted noise level of the power tool are: 94

dB(A); sound power level 102 dB(A). Uncertainty K = 3 dB.

Wear hearing protection!

Vibration total values ah (triax vector sum) and uncertainty K

determined according to ENIEC62841-2-3:

Surface grinding (roughing) and abrasive cutting:

ah=8.5 m/s2, K=1.5 m/s2,

Disc sanding:

ah=3.0 m/s2, K=1.5 m/s2.

Grinding thin metal sheets or other materials that tend to easily vi-

brate with a large surface area can cause the noise emission value to

increase by up to 15dB. Suitable, heavy damping mats can reduce

the increased noise emissions. Increased noise emissions must be

taken into consideration, both for the risk assessment of the noise

output and for selecting suitable hearing protection.

The vibration level and noise emission value given in these

instructions have been measured in accordance with a

standardised measuring procedure and may be used to com-

pare power tools. They may also be used for a preliminary

estimation of vibration and noise emissions.

The stated vibration level and noise emission value repres-

ent the main applications of the power tool. However, if the

power tool is used for other applications, with different ap-

plication tools or is poorly maintained, the vibration level

and noise emission value may differ. This may significantly

increase the vibration and noise emissions over the total

working period.

To estimate vibration and noise emissions accurately, the

times when the tool is switched off or when it is running but

not actually being used should also be taken into account.

This may significantly reduce vibration and noise emissions

over the total working period.

Implement additional safety measures to protect the oper-

ator from the effects of vibration, such as servicing the

power tool and application tools, keeping their hands warm,

and organising workflows correctly.

Restart protection

The restart protection feature prevents the power tool from

uncontrolled starting after the power supply to it has been

interrupted.

To restart the tool, set the on/off switch (4) to the "off" posi-

tion and then switch the power tool on again.

In rare cases, certain interference pulses can cause the re-

start protection to activate. In such cases, the power tool

switches off and stays switched off. The power tool can be

started up again by releasing the on/off switch(4) and

pressing it again.

Soft start

The electronic soft start limits the torque when the power

tool is switched on and enables a smooth start-up.

Note: If the power tool runs at full speed immediately after

being switched on, this means that the soft start and restart

protection mechanisms have failed. The power tool must be

sent to the after-sales service immediately; see the "After-

Sales Service and Application Service" section for ad-

dresses.

Constant Electronic Control (GWX 14-125)

The Constant Electronic keeps the speed at no load and un-

der load virtually consistent, guaranteeing uniform perform-

ance.

Fitting

Fitting Protective Equipment

uPull the plug out of the socket before carrying out any

work on the power tool.

Note: If the grinding disc breaks during operation or the

holding fixtures on the protective guard/power tool become

damaged, the power tool must be sent to the after-sales ser-

vice immediately; see the "After-Sales Service and Applica-

tion Service" section for addresses.

Protective guard for grinding

Place the protective guard

(7) onto the holder on the

power tool until the coding

cams of the protective guard

are aligned with the holder.

When doing so, press and

hold the unlocking lever (1).

Press the protective guard

(7) onto the spindle collar un-

til the shoulder of the pro-

tective guard is sitting on the

flange of the power tool and

rotate the protective guard

until it audibly clicks into

place.

Adjust the position of the protective guard (7) to meet the

requirements of the operation. To do this, push the unlock-

ing lever (1) upward and rotate the protective guard (7) into

the required position.

1 609 92A 765 | (17.03.2022) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GWX 14-125 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info