Bedienungsanleitung Bosch GWX 15-125 PS (Seite 21 von 301) (Alle Sprachen)

786312

Zoom out

Zoom in

Vorherige Seite

1/301

Nächste Seite

English | 21

(3) (3)

Cup brushes/disc brushes and fibre discs

uAlways fit the hand guard (16) when working with the

cup brush/disc brush or fibre disc.

See the graphics page for fitting instructions.

To remove an application tool, open the lever (3) and re-

move the application tool.

Approved abrasive tools

You can use all the abrasive tools mentioned in these operat-

ing instructions.

The permissible speed [rpm] or the circumferential speed

[m/s] of the abrasive tools used must at least match the val-

ues given in the table.

It is therefore important to observe the permissible rota-

tional/circumferential speed on the label of the abrasive

tool.

max. [mm] [mm]

D b d [min-1] [m/s]

125 7 22.2 11,500 80

125 – – 11,500 80

75 30 – 11,500 45

82 – – 11,500 80

Rotating the machine head

uPull the plug out of the socket before carrying out any

work on the power tool.

The machine head can be

rotated in 90° increments.

In this way, the on/off

switch can be brought into

a more favourable handling

position for particular ap-

plications, e.g. for left-

handed tool users.

Completely unscrew the

four screws. Rotate the ma-

chine head carefully, without removing it from the hous-

ing, into the new position. Screw in and retighten the four

screws.

Dust/chip extraction

The dust from materials such as lead paint, some types of

wood, minerals and metal can be harmful to human health.

Touching or breathing in this dust can trigger allergic reac-

tions and/or cause respiratory illnesses in the user or in

people in the near vicinity.

Certain dusts, such as oak or beech dust, are classified as

carcinogenic, especially in conjunction with wood treatment

additives (chromate, wood preservative). Materials contain-

ing asbestos may only be machined by specialists.

– Use a dust extraction system that is suitable for the ma-

terial wherever possible.

– Provide good ventilation at the workplace.

– It is advisable to wear a P2 filter class breathing mask.

The regulations on the material being machined that apply in

the country of use must be observed.

uAvoid dust accumulation at the workplace. Dust can

easily ignite.

Operation

Start-up

uPay attention to the mains voltage. The voltage of the

power source must match the voltage specified on the

rating plate of the power tool. Power tools marked

with 230V can also be operated with 220V.

When operating the power tool using a mobile generator that

does not have sufficient reserve capacity or an adequate

voltage control system with inrush current boost converter,

loss of performance or atypical behaviour may occur upon

switch-on.

Please check the suitability of the power generator you are

using, particularly with regard to the mains voltage and fre-

quency.

uProducts that are only sold in AUS and NZ: Use a resid-

ual current device (RCD) with a nominal residual current

of 30 mA or less.

Bosch Power Tools 1 609 92A 4F9 | (10.01.2019)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GWX 15-125 PS Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info