Bedienungsanleitung Bosch LR 60 (Seite 21 von 253) (Alle Sprachen)

786509

Zoom out

Zoom in

Vorherige Seite

1/253

Nächste Seite

English | 21

Marking

You can mark the position of the laser beam at the centre

mark(9) on the left and right of the laser receiver when the

beam hits the centre of the reception area(1).

When marking, take care to align the laser receiver so that it

is exactly vertical (with a horizontal laser beam) or horizontal

(with a vertical laser beam), as otherwise the marks are off-

set with respect to the laser beam.

Attaching using the holder (seefigureE)

You can use the holder(23) to attach the laser receiver to a

measuring rod(25) (accessory) as well as to other auxiliary

tools with a width of up to 65mm.

Screw the holder(23) to the mount(11) on the rear side of

the laser receiver with the fastening screw(26).

Loosen the rotary knob(24) on the holder, slide the holder

onto the measuring rod(25) and retighten the rotary

knob(24).

You can use the spirit level(21) to ensure that the

holder(23) is horizontally aligned along with the laser re-

ceiver. If the laser receiver is mounted at an angle, it will give

incorrect measurements.

The centre line reference(22) on the holder is situated at

the same height as the centre marking(9) and can be used

for marking the laser beam.

Attaching using a magnet (see figure F)

If an attachment is not required to be especially secure, the

laser receiver can be attached to steel parts using the

magnets(10).

Rectifying errors

Text display (e) Problem Corrective measures

PNK Failed to establish Bluetooth® connec-

tion to the GRL600CHV or

GRL650CHVG rotary laser

Briefly press the on/off button on the rotary laser to close

the error message. Restart the process for establishing

the connection.

If it is not possible to establish a connection, please con-

tact a Bosch customer service agent.

ERR Calibration of the GRL600CHV or

GRL650CHVG rotary laser failed Read and observe the operating instructions for the

GRL600CHV or GRL650CHVG.

CenterFind mode or CenterLock mode

failed

Press any button to close the error message. Check the

position of the rotary laser and laser receiver before re-

starting the function.

LR65G:

ERR and CL in alterna-

tion CenterFind mode cannot be started be-

cause the rotary laser is already working

in CenterLock mode.

Select CenterFind mode on both laser receivers and re-

start the function.

ERR and CF in alterna-

tion CenterLock mode cannot be started

because the rotary laser is already

working in CenterFind mode.

Select CenterLock mode on both laser receivers and re-

start the function.

Assignment of Functions

Function possible with LR 60 and GRL 600 CHV Rotary laser with red laser beam

(600−800nm)

Battery charge indicator of the rotary laser ● –

Direction indicators for the position of the laser beam ● ●

Relative height indicator ● ●

CenterFind mode ● –

CenterLock mode – –

Function possible with LR 65G and GRL 650 CHVG Rotary laser with green laser beam

(500−570nm)

Battery charge indicator of the rotary laser ● –

Direction indicators for the position of the laser beam ● ●

Relative height indicator ● ●

CenterFind mode ● –

CenterLock mode ● –

Bosch Power Tools 1 609 92A 7M6 | (12.05.2022)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch LR 60 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info