Bedienungsanleitung Bosch LR 60 (Seite 19 von 253) (Alle Sprachen)

786509

Zoom out

Zoom in

Vorherige Seite

1/253

Nächste Seite

English | 19

–LED direction indicators (LED): The 3 LED direction

indicators(2), (4) and (3) can be adjusted with regard to

their brightness or switched off. The LEDs light up in their

selected setting.

–Display lighting (LIT): The display lighting can be

switched on (green LED lights up) or switched off (red

LED lights up).

–Memory function for last reception (MEM): The indic-

ator for the direction in which the laser beam has left the

reception area can be switched on (green LED lights up)

or switched off (red LED lights up).

–Centre functions (CF/CL) (LR65G): You can choose

between CenterFind (CF) mode and CenterLock (CL)

mode. The current mode appears in the text display(e).

With the exception of the setting for the display lighting, all

settings are saved when the laser receiver is switched off.

Functions

CenterFind mode (see figureC)

In CenterFind mode, the rotary laser automatically attempts

to align the laser beam to the centre line of the laser receiver

by moving the rotation head up and down.

If the rotary laser is in the horizontal position, the laser

beam can be aligned in relation to the X-axis of the rotary

laser, to the Y-axis or to both axes at the same time (see "In-

clination determination with CenterFind mode (see

figureD)", page19). If the rotary laser is in the vertical po-

sition, only alignment to the Y-axis is possible.

Start CenterFind mode:

Position the rotary laser and laser receiver so that the laser

receiver is situated in the direction of the X-axis or the Y-axis

of the rotary laser. Align the laser receiver so that the re-

quired axis is at a right angle to the reception area(1).

If the laser beam is aligned to both axes, then place a laser

receiver connected to the rotary laser in the direction of the

X- and Y-axis respectively. Each laser receiver must be situ-

ated within the pivoting range of ±8.5% of the rotary laser.

Switch on the rotary laser in rotational operation.

LR65G: In the settings menu, the centre function must be

put in CenterFind (CF) mode. When aligning to two axes of

the rotary laser, this applies to both laser receivers.

To start the CenterFind mode for the X‑axis, either press

and hold the CenterFind(17) mode button, or press and

hold the CenterFind(17) mode button, together with the

X‑axis button(16).

To start the CenterFind mode for the Y-axis, press and hold

the CenterFind(17) mode button, together with the Y‑axis

button(15).

Should the laser beam be aligned to both axes at the same

time, CenterFind mode must be started separately on each

laser receiver.

Following the start of CenterFind mode, the rotary head on

the rotary laser moves up and down. During the search pro-

cess, CFX (X‑axis) or CFY (Y‑axis) appears in the text

display(e).

If the laser beam hits the reception area(1) at the height of

the centre line of the laser receiver, the centre line

indicator(h) will appear andXOK (X axis) and YOK (Y axis)

will appear in the text display(e). The value of the incline

that is found is displayed on the rotary laser. CenterFind

mode will be ended automatically.

Cancelling CenterFind mode:

To cancel the CenterFind mode, press and hold the

CenterFind mode button(17).

Troubleshooting:

If the laser beam was unable to find the centre line of the

laser receiver within the pivoting range, ERR appears in the

text display(e) and all LED direction indicators light up.

Press any button on the rotary laser and one on the laser re-

ceiver to close the error messages. Reposition the rotary

laser and laser receiver so that the laser receiver is situated

within the pivoting range of ±8.5% of the rotary laser. En-

sure that the laser receiver is aligned to the X-axis or Y-axis

so that the laser beam can pass through the reception

area(1) horizontally. Then restart the CenterFind mode.

LR65G: If both axes of the rotary laser should be aligned to

a laser receiver, the same centre function must be set on

both laser receivers. A combination of CenterFind mode

andCenterLock mode is not possible.

IfCenterLock mode is already set on one axis

andCenterFind mode is started on the other axis,ERR

andCL will appear alternately in the text display(e).

SelectCenterFind mode on both laser receivers and re-start

the function.

Inclination determination with CenterFind mode (see

figureD)

Using CenterFind mode, the inclination of a surface can be

measured up to max. 8.5%. To do this, set up the rotary

laser at one end of the inclined surface in a horizontal posi-

tion on a tripod. The X- or Y-axis of the rotary laser must be

aligned with the inclination to be determined. Switch on the

rotary laser and allow it to level in.

Secure the laser receiver to a measuring rod(25) with the

holder. Place the measuring rod near to the measuring tool

(at the same end of the inclined surface). Align the height of

the laser receiver on the measuring rod so that the laser

beam of the rotary laser is indicated as "centred" .

Bosch Power Tools 1 609 92A 7M6 | (12.05.2022)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch LR 60 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info