Bedienungsanleitung Bosch LR 60 (Seite 17 von 253) (Alle Sprachen)

786509

Zoom out

Zoom in

Vorherige Seite

1/253

Nächste Seite

English | 17

Indicator Capacity

0 − 2%

Always replace all the batteries at the same time. Only use

batteries from the same manufacturer and which have the

same capacity.

uTake the batteries out of the laser receiver when you

are not using it for a prolonged period of time. The bat-

teries can corrode and self-discharge during prolonged

storage in the laser receiver.

Rotary Laser Battery Charge Indicator

The battery charge indicator(a) shows the state of charge of

the battery pack/batteries of the rotary laser, provided that

the rotary laser is switched on and a Bluetooth® connection

has been established between the laser receiver and the

rotary laser.

Indicator Capacity

60 − 100%

30 − 60%

5 − 30%

0 − 5%

Operation

Starting operation

uProtect the laser receiver against moisture and direct

sunlight.

uDo not subject the laser receiver to extreme temperat-

ures or variations in temperature. As an example, do

not leave it in vehicles for longer periods. In case of large

variations in temperature, allow the laser receiver to ad-

just to the ambient temperature before putting it into op-

eration. In case of extreme temperatures or variations in

temperature, the accuracy of the laser receiver can be im-

paired.

uKeep the work area free from obstacles that could re-

flect or obstruct the laser beam. For example, cover

any reflective or shiny surfaces. Do not measure

through panes of glass or similar materials. The meas-

urements may be distorted by a reflected or obstructed

laser beam.

Setting up the laser receiver (seefigureA)

Position the laser receiver so that the laser beam can reach

the reception area(1). Align it so that the laser beam runs

straight through the reception area (as shown in the figure).

For rotary lasers with multiple operating modes, select the

horizontal or vertical operation with the highest rotational

speed.

Switching On/Off

uA loud audio signal sounds when switching on the

laser receiver. Therefore, keep the laser receiver

away from your ear or other persons when switching it

on. The loud sound can damage hearing.

To switch on the laser receiver, press the on/off

button(19). All display indicators and all LEDs light up

briefly and an audio signal sounds.

To switch off the laser receiver, press and hold the on/off

button(19) until all LEDs briefly light up and the display

goes out. With the exception of the setting for the display

lighting, all settings are saved when the laser receiver is

switched off.

If no button on the laser receiver is pressed for approx.

10min and no laser beam reaches the reception area(1) for

10min, then the laser receiver will automatically switch it-

self off to preserve battery life.

Connection to the Rotary Laser

In the default factory setting, the rotary laser and the sup-

plied laser receiver are already connected via Bluetooth®.

For the existing connection, the Bluetooth® connection

indicator(b) appears in the display of the laser receiver.

To reconnect the laser receiver or to connect an additional

laser receiver with the rotary laser, press and hold the

Bluetooth® button on the rotary laser until the symbol for es-

tablishing a connection to the remote control/laser receiver

appears in the display of the rotary laser. Then press and

hold the X‑axis button(16) and Y‑axis button(15) on the

laser receiver untilP‑‑ appears in the text display(e).

Confirmation as to whether a connection has successfully

been established will be shown on the display of the rotary

laser. POK will appear on the text indicator(e) of the laser

receiver.

If the connection between the rotary laser and the laser re-

ceiver cannot be established, PNK will appear in the text

display(e) of the laser receiver and the error message for a

failed connection will be shown in the display of the rotary

laser. For troubleshooting, consult the operating instruc-

tions for the rotary laser.

Direction indicators

The position of the laser beam in the reception area(1) is in-

dicated as follows:

– On the display(5) on the front and rear of the laser re-

ceiver by means of the "laser beam below centre line" dir-

ection indicator(f), the "laser beam above centre line"

direction indicator(j) and the centre line indicator(h)

– Optionally, by means of the red "laser beam below centre

line" LED direction indicator(4), the blue "laser beam

above centre line" LED direction indicator(2) and the

green centre line LED(3) on the front of the laser receiver

– By an audio signal (optional).

On the first pass of the laser beam through the reception

area(1) a short audio signal always sounds and the red

"laser beam below centre line" LED direction indicator(4)

and the blue "laser beam above centre line" LED direction

Bosch Power Tools 1 609 92A 7M6 | (12.05.2022)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch LR 60 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info