Bedienungsanleitung Bosch pbh 2900 fre (Seite 26 von 158) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

388876

Zoom out

Zoom in

Vorherige Seite

1/158

Nächste Seite

26 | English

1 609 929 T39 | (19.11.10) Bosch Power Tools

Dust Extraction with the Dust Extrac-

tion Attachment (Accessory)

f Dusts from materials such as lead-containing

coatings, some wood types, minerals and

metal can be harmful to one’s health. Touch-

ing or breathing-in the dusts can cause aller-

gic reactions and/or lead to respiratory infec-

tions of the user or bystanders.

Certain dusts, such as oak or beech dust, are

considered as carcinogenic, especially in

connection with wood-treatment additives

(chromate, wood preservative). Materials

containing asbestos may only be worked by

specialists.

– As far as possible, use a dust extraction

system suitable for the material.

– Provide for good ventilation of the work-

ing place.

– It is recommended to wear a P2 filter-

class respirator.

Observe the relevant regulations in your

country for the materials to be worked.

f Prevent dust accumulation at the work-

place. Dusts can easily ignite.

Mounting the Dust Extraction Attachment

(see figure K)

For dust extraction, the dust extraction attach-

ment (accessory) is required. When drilling, the

dust extraction attachment retracts so that the

attachment head is always close to the surface

at the drill hole.

– Press the button for depth stop adjustment

15 and remove the depth stop 18. Press but-

ton 15 again and insert the dust extraction

attachment into the auxiliary handle 17 from

the front.

– Connect an extraction hose (diameter

19 mm, accessory) to the extraction sleeve

27 of the dust extraction attachment.

The vacuum cleaner must be suitable for the ma-

terial being worked.

When vacuuming dry dust that is especially det-

rimental to health or carcinogenic, use a special

vacuum cleaner.

Adjusting the Drilling Depth on the Dust Ex-

traction Attachment (see figure L)

The required drilling depth X can also be adjust-

ed when the dust extraction attachment is

mounted.

– Insert the SDS-plus drilling tool to the stop

into the SDS-plus tool holder 3. Otherwise,

the movability of the SDS-plus drilling tool

can lead to incorrect adjustment of the drill-

ing depth.

– Loosen the wing bolt 31 on the dust extrac-

tion attachment.

– Without switching the power tool on, apply it

firmly to the drilling location. The SDS-plus

drilling tool must face against the surface.

– Position the the guide pipe 32 of the dust ex-

traction attachment in its holding fixture in

such a manner that the head of the dust ex-

traction attachment faces against the surface

to be drilled. Do not slide the guide pipe 32

further over the telescopic pipe 30 of the

dust extraction attachment than required, so

that as much as possible of the scale 30 on

the telescopic pipe remains visible.

– Retighten the wing bolt 31 again. Loosen the

clamping screw 28 on the depth stop of the

dust extraction attachment.

–Move the depth stop 29 on the telescopic

pipe 30 in such a manner that the

clearance

X shown in the figure corresponds

with the required drilling depth.

– Tighten the clamping screw 28 in this posi-

tion.

OBJ_BUCH-318-003.book Page 26 Friday, November 19, 2010 4:36 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch pbh 2900 fre Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info