Bedienungsanleitung Bosch pbh 2900 fre (Seite 25 von 158) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

388876

Zoom out

Zoom in

Vorherige Seite

1/158

Nächste Seite

English | 25

Bosch Power Tools 1 609 929 T39 | (19.11.10)

Changing the Tool

The dust protection cap 4 largely prevents the

entry of drilling dust into the tool holder during

operation. When inserting the tool, take care

that the dust protection cap 4 is not damaged.

f A damaged dust protection cap should be

changed immediately. We recommend hav-

ing this carried out by an after-sales serv-

ice.

Inserting SDS-plus Drilling Tools

(see figure G)

The SDS-plus drill chuck allows for simple and

convenient changing of drilling tools without the

use of additional tools.

– PBH 3000-2 FRE: Insert the SDS-plus quick

change chuck 2.

– Clean and lightly grease the shank end of the

tool.

– Insert the tool in a twisting manner into the

tool holder until it latches itself.

– Check the latching by pulling the tool.

As a requirement of the system, the SDS-plus

drilling tool can move freely. This causes a cer-

tain radial run-out at no-load, which has no ef-

fect on the accuracy of the drill hole, as the drill

bit centres itself upon drilling.

Removing SDS-plus Drilling Tools

(see figure H)

– Push back the locking sleeve 5 and remove

the tool.

Inserting Drilling Tools without SDS-plus into

the Key Type Drill Chuck (PBH 2800 RE)

Note: Do not use tools without SDS-plus for

hammer drilling or chiselling! Tools without

SDS-plus and their drill chucks are damaged by

hammer drilling or chiselling.

– Insert the key type drill chuck 21.

– Open the key type drill chuck 21 by turning

until the tool can be inserted. Insert the tool.

– Insert the chuck key into the corresponding

holes of the key type drill chuck 21 and clamp

the tool uniformly.

– Turn the mode selector switch 12 to the

“drilling” position.

Removing Drilling Tools without SDS-plus from

the Key Type Drill Chuck (PBH 2800 RE)

– Turn the sleeve of the key type drill chuck 21

with the drill chuck key in anticlockwise di-

rection until the drilling tool can be removed.

Inserting Drilling Tools without SDS-plus into

the Keyless Chuck

(PBH 2900 FRE/PBH 3000 FRE Set/

PBH 3000-2 FRE) (see figure I)

Note: Do not use tools without SDS-plus for

hammer drilling or chiselling! Tools without

SDS-plus and their drill chucks are damaged by

hammer drilling or chiselling.

– PBH 2900 FRE/PBH 3000 FRE Set: Insert the

keyless chuck 23.

– PBH 3000-2 FRE: Insert the quick change

keyless chuck 1.

– Hold the rear sleeve 26 of the keyless chuck

23 and turn the front sleeve 25 in anticlock-

wise direction until until the tool can be in-

serted. Insert the tool.

– Tightly hold the rear sleeve of the keyless

chuck 23 and firmly turn the front sleeve

clockwise by hand until the locking action is

no longer heard. This automatically locks the

drill chuck.

– Check the tight seating by pulling the tool.

Note: If the tool holder was opened to the stop,

then a latching noise possibly may be heard

while closing the tool holder and the tool holder

will not close.

In this case, turn the front sleeve 25 once in an-

ticlockwise direction. Afterwards, the tool hold-

er can be closed (tightened).

– Turn the mode selector switch 12 to the

“drilling” position.

Removing Drilling Tools without SDS-plus from

the Keyless Chuck

(PBH 2900 FRE/PBH 3000 FRE Set/

PBH 3000-2 FRE) (see figure J)

– Firmly hold the rear sleeve 26 of the keyless

chuck and turn the front sleeve 25 of the key-

less chuck in anticlockwise direction until

the drilling tool can be removed.

OBJ_BUCH-318-003.book Page 25 Friday, November 19, 2010 4:36 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch pbh 2900 fre Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info