Bedienungsanleitung Bosch PBH300E (Seite 19 von 109) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

32141

Zoom out

Zoom in

Vorherige Seite

1/109

Nächste Seite

English | 19

Bosch Power Tools 1 619 929 766 | (26.7.07)

Note: Do not use tools without SDS-plus for ham-

mer drilling or chiselling! Tools without SDS-plus

and their drill chucks are damaged by hammer

drilling or chiselling.

The SDS-plus tool holder 1 can easily be ex-

changed against the quick change keyless chuck

10.

Changing the Tool Holder

Dismounting the SDS-plus Tool Holder or the

Quick change keyless chuck (see figure B)

Turn the mode selector switch 6 temporarily to

the “drilling” position in order to lock the tool

holder.

Firmly turn the locking sleeve 3 in the direction of

the arrow and pull off the tool holder 1 or the

quick change keyless chuck 10 toward the front.

After removing, protect the tool holder 1 or the

quick change keyless chuck 10 against contami-

nation. Lightly lubricate the engaging grooves, if

required.

Mounting the SDS-plus Tool Holder or the Quick

change keyless chuck

Turn the locking sleeve 3 in the direction of the

arrow and pull it back at the same time, until the

tool holder 1 or the quick change keyless chuck

10 engages.

The tool holder 1 or the quick change keyless

chuck 10 is automatically locked. Check the lock-

ing effect by pulling the tool holder.

Changing the Tool

With the SDS-plus tool holder, simple and con-

venient tool changing is possible without addi-

tional aids.

As a requirement of the system, the SDS-plus

drilling tool can move freely. This causes a cer-

tain radial run-out at no-load, which has no effect

on the accuracy of the drill hole, as the drill bit

centres itself upon drilling.

The dust protection cap 2 largely prevents the

entry of drilling dust into the tool holder during

operation. When inserting the tool, take care that

the dust protection cap 2 is not damaged.

f A damaged dust protection cap should be

changed immediately. We recommend hav-

ing this carried out by an after-sales service.

Inserting SDS-plus Drilling Tools (see figure C)

Clean and lightly grease the shank end of the

tool.

Insert the tool in a twisting manner into the tool

holder until it latches itself.

Check the latching by pulling the tool.

Removing SDS-plus Drilling Tools (see figure D)

Push back the locking sleeve 3 and remove the

tool.

Inserting Drilling Tools without SDS-plus

(see figure E)

Note: Do not use tools without SDS-plus for ham-

mer drilling or chiselling! Tools without SDS-plus

and their drill chucks are damaged by hammer

drilling or chiselling.

Insert the quick change keyless chuck 10.

Firmly hold the retaining ring of the quick change

keyless chuck 10. Open the quick change keyless

chuck by turning the front sleeve in the direction

of the symbol “ ”.

Insert the drilling tool into the quick change key-

less chuck 10. Firmly hold the retaining ring of

the quick change keyless chuck 10 and turn the

front sleeve in the direction of the symbol

“ ”.

Check the tight seating by pulling the tool.

Note: If the tool holder was opened to the stop,

then the latching noise possibly may be heard

while closing the tool holder and the tool holder

will not close.

In this case, turn the front sleeve 11 once in the

opposite direction of the arrow. Afterwards, the

tool holder can be closed (tightened) again.

Turn the mode selector switch 6 to the “drilling”

position.

Removing Drilling Tools without SDS-plus

(see figure E)

Firmly hold the retaining ring of the quick change

keyless chuck 10. Open the quick change keyless

chuck by turning the front sleeve in the direction

of the symbol “ ”.

Remove the drilling tool.

OBJ_BUCH-440-001.book Page 19 Thursday, July 26, 2007 9:22 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PBH300E Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch PBH300E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info