Bedienungsanleitung Bosch PBH300E (Seite 20 von 109) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

32141

Zoom out

Zoom in

Vorherige Seite

1/109

Nächste Seite

1 619 929 766 | (26.7.07) Bosch Power Tools

20 | English

Operation

Starting Operation

f Observe correct mains voltage! The voltage

of the power source must agree with the

voltage specified on the nameplate of the

machine. Power tools marked with 230 V can

also be operated with 220 V.

Setting the Operating Mode

The operating mode of the power tool is selected

with the mode selector switch 6.

Note: Change the operating mode only when the

machine is switched off! Otherwise, the machine

can be damaged.

Press and hold the unlocking button 5 and turn

the mode selector switch 6 to the required posi-

tion.

Switching On and Off

To start the machine, press the On/Off switch 4

and keep it depressed.

To switch off the machine, release the On/Off

switch 4.

For low temperatures, the power tool reaches

the full hammer/impact capacity only after a cer-

tain time.

Setting the Speed/Impact Rate

The speed/impact rate of the switched on power

tool can be variably adjusted, depending on how

far the On/Off switch 4 is pressed.

Light pressure on the On/Off switch 4 results in

low speed/impact rate. Further pressure on the

switch increases the speed/impact rate.

Overload Clutch

f If the tool insert becomes caught or jammed,

the drive to the drill spindle is interrupted.

Because of the forces that occur, always

hold the power tool firmly with both hands

and provide for a secure stance.

f If the power tool jams, switch the machine

off and loosen the tool insert. When switch-

ing the machine on with the drilling tool

jammed, high reaction torques can occur.

Changing the Chiselling Position (Vario-Lock)

The chisel can be locked in 36 positions. In this

manner, the optimum working position can be

set for each application.

Insert the chisel into the tool holder.

Press and hold the unlocking button 5 and turn

the mode selector switch 6 to “Changing the

chiselling position (Vario-lock)”.

Turn the tool holder to the desired chiselling po-

sition.

Press and hold the unlocking button 5 and turn

the mode selector switch 6 to the “Chiselling”

position. The tool holder is locked in this posi-

tion.

For chiselling, set the rotation direction to right

rotation.

Maintenance and Service

Maintenance and Cleaning

f Before any work on the machine itself, pull

the mains plug.

f For safe and proper working, always keep

the machine and ventilation slots clean.

f A damaged dust protection cap should be

changed immediately. We recommend hav-

ing this carried out by an after-sales service.

Position for drilling without impact

in wood, metal, ceramic and plastic

Position for hammer drilling in con-

crete or stone

When the drilling tool does not im-

mediately rotate upon switching on,

allow the machine to run slowly un-

til the drilling tool rotates.

Vario-Lock position for adjustment

of the chiselling position

Position for chiselling

OBJ_BUCH-440-001.book Page 20 Thursday, July 26, 2007 9:22 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PBH300E Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch PBH300E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info