Bedienungsanleitung Bosch PCM 7 (Seite 31 von 346) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544038

Zoom out

Zoom in

Vorherige Seite

1/346

Nächste Seite

English | 31

Bosch Power Tools 1 609 929 U75 | (19.7.10)

Working Advice

General Sawing Instructions

f For all cuts, it must first be ensured that the

saw blade at no time can come in contact

with the fence, screw clamps or other ma-

chine parts. Remove possibly mounted aux-

iliary stops or adjust them accordingly.

Protect the saw blade against impact and shock.

Do not subject the saw blade to lateral pressure.

Do not saw warped/bent workpieces. The work-

piece must always have a straight edge to face

against the fence.

Long workpieces must be underlaid or support-

ed at their free end.

Marking the Cutting Line (see figure J)

A laser beam indicates the cutting line of the

saw blade. This allows for exact positioning of

the workpiece for sawing, without having to

open the retracting blade guard.

– For this, switch the laser beam on with the

switch 20.

– Align the cutting mark on your workpiece

with reference to the right-hand edge of the

laser line.

Position of the Operator (see figure K)

f Do not stand in a line with the saw blade in

front of the machine. Always stand aside of

the saw blade. This protects your body

against possible kickback.

– Keep hands, fingers and arms away from the

rotating saw blade.

– Do not cross your arms when operating the

tool arm.

Permissible Workpiece Dimensions

Maximal workpiece sizes:

Minimal workpiece sizes

(= all workpieces that can be clamped left or

right from the saw blade with the supplied ma-

terial clamp 14): 100 x 40 mm (length x width)

Cutting capacity, max. (0°/0°): 50 mm

Cutting Off

– Firmly clamp the workpiece as appropriate

for its dimensions.

– Adjust the requested horizontal and/or verti-

cal mitre/bevel angle.

– Switch on the machine.

– Press lever 3 and slowly guide the tool arm

downward by handle 1.

– Saw through the workpiece applying uniform

feed.

– Switch off the machine and wait until the

saw blade has come to a complete stop.

– Guide the tool arm slowly upward.

Replacing the Insert Plate

The red insert plate 7 can become worn after

long use of the power tool.

Replace defective insert plates.

– Bring the power tool into the working posi-

tion.

– Unscrew screws 8 using a Phillips screwdriv-

er and remove the old insert plate.

– Insert the new insert plate and and screw all

screws 8 in again.

Sawing Profile Strips

Profile strips/mouldings can be sawn in two dif-

ferent ways:

Always make trial cuts with the mitre angle set-

ting first on scrap wood.

Mitre/Bevel Angle Height x Width

Horizontal Vertical

0° 0°

50 x 110 mm

45° 0°

50 x 76 mm

0° 45°

37 x 110 mm

45° 45°

37 x 76 mm

– Placed against the fence

– Lying flat on the saw

table

OBJ_BUCH-880-004.book Page 31 Monday, July 19, 2010 11:56 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PCM 7 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info