Bedienungsanleitung Bosch PCM 7 (Seite 29 von 346) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544038

Zoom out

Zoom in

Vorherige Seite

1/346

Nächste Seite

English | 29

Bosch Power Tools 1 609 929 U75 | (19.7.10)

External Dust Extraction

For dust extraction, a vacuum hose (size

Ø 36 mm) can also be connected to the dust

ejector 21.

The vacuum cleaner must be suitable for the ma-

terial being worked.

When vacuuming dry dust that is especially det-

rimental to health or carcinogenic, use a special

vacuum cleaner.

Changing the Tool (see figures D1– D4)

f Before any work on the machine itself, pull

the mains plug.

f When mounting the saw blade, wear protec-

tive gloves. Danger of injury when touching

the saw blade.

Use only saw blades whose maximum permitted

speed is higher than the no-load speed of the

power tool.

Use only saw blades that correspond with the

characteristic data given in these operation in-

structions and that are tested and marked in ac-

cordance with EN 847-1.

Use only saw blades recommended by the tool

manufacturer, and suitable for sawing the mate-

rials to be cut.

Removing the Saw Blade

– Bring the power tool into the working posi-

tion.

– Turn the Allen screw 30 with the Allen key 22

provided while at the same time pressing the

spindle lock 28 until it engages.

– Hold the spindle lock 28 pressed and un-

screw the Allen screw 30 in clockwise direc-

tion (left-hand thread!).

– Remove the clamping flange 31.

– Press lever 3 and swing back the retracting

blade guard 5 to the stop.

– Hold the retracting blade guard in this posi-

tion and remove the saw blade 17.

– Slowly guide the retracting blade guard

downward again.

Mounting the Saw Blade

If required, clean all parts to be mounted prior

to assembly.

– Press lever 3, swing back the retracting

blade guard 5 to the stop and hold it in this

position.

– Place the new saw blade onto the interior

clamping flange 32.

f When mounting the saw blade, pay atten-

tion that the cutting direction of the teeth

(arrow direction on the saw blade) corre-

sponds with the direction of the arrow on

the blade guard!

– Slowly guide the retracting blade guard

downward again.

– Place on the clamping flange 31 and the

screw 30.

Press the spindle lock 28 until it engages and

tighten the screw turning in anticlockwise di-

rection.

Operation

f Before any work on the machine itself, pull

the mains plug.

Transport Safety (see figure E)

The transport safety-lock 24 enables easier han-

dling of the machine when transporting to vari-

ous working locations.

Releasing the Machine (Working Position)

– Push the tool arm by the handle 1 down a lit-

tle in order to relieve the transport safety-

lock 24.

– Pull the transport safety-lock 24 completely

outward.

– Guide the tool arm slowly upward.

Securing the Machine (Transport Position)

– Tighten clamping lever 25 to lock the saw ta-

ble 11.

– Press lever 3 and at the same time, swing the

tool arm by handle 1 toward the rear until the

transport safety-lock 24 can be pushed com-

pletely inward.

The tool arm is now securely locked for trans-

port.

OBJ_BUCH-880-004.book Page 29 Monday, July 19, 2010 11:56 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PCM 7 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info