Bedienungsanleitung Bosch PDR 18 LI (Seite 13 von 179) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

708153

Zoom out

Zoom in

Vorherige Seite

1/179

Nächste Seite

Typically the A-weighted noise level of the power tool is:

Sound pressure level 95 dB(A); Sound power level

106dB(A). Uncertainty K=3 dB.

Wear hearing protection

Total vibration values a

(triax vector sum) and uncertainty K

determined according to EN 62841-2-2:

Impact tightening of fasteners of the maximum capacity of

the tool: a

=11 m/s

, K=1.8 m/s

The vibration level and noise emission value given in these

instructions have been measured in accordance with a

standardised measuring procedure detailed in EN 62841

and may be used to compare power tools. They may also be

used for a preliminary estimation of vibration and noise

emissions.

The given vibration level and noise emission value represent

the main applications of the power tool. However, if the

power tool is used for other applications, with different ap-

plication tools or is poorly maintained, the vibration level

and noise emission value may differ. This may significantly

increase the vibration and noise emissions over the total

working period.

To estimate vibration and noise emissions accurately, the

times when the tool is switched off or when it is running but

not actually being used should also be taken into account.

This may significantly reduce vibration and noise emissions

over the total working period.

Implement additional safety measures to protect the oper-

ator from the effects of vibration, such as servicing the

power tool and application tools, keeping the hands warm,

and organising workflows correctly.

Assembly

u Remove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Charge battery (see figureA)

Note: The battery is supplied partially charged. To ensure

full battery capacity, fully charge the battery in the charger

before using your power tool for the first time.

The lithium-ion battery can be charged at any time without

reducing its service life. Interrupting the charging process

does not damage the battery.

The lithium-ion battery is protected against deep discharge

by the "Electronic Cell Protection (ECP)". When the battery

is discharged, the power tool is switched off by means of a

protective circuit: The application tool no longer rotates.

u Do not continue to press the On/Off switch after the

power tool has automatically switched off. The battery

can be damaged.

– To remove the battery (4), press the release button (3)

and pull the battery back and out of the power tool. Do

not use force to do this.

You can also leave the battery (4) inserted in the power tool

for charging. While it is charging, the power tool cannot be

switched on.

Follow the instructions on correct disposal.

Changing the tool (see figure B)

u Remove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Inserting the application tool

– Pull the locking sleeve (2) forward, guide the application

tool (1) into the tool holder up to the stop and release the

locking sleeve (2) to lock the application tool.

– Use only screwdriver bits with ball catch (8) (DIN 3126-

E6.3). Other screwdriver bits (9) can be inserted using a

universal bit holder with ball catch (10).

Removing the application tool

– Pull the locking sleeve (2) forward and remove the applic-

ation tool.

Operation

How it works

The tool holder (1) (with the application tool) is driven by an

electric motor via a gear and impact mechanism. The work-

ing procedure is divided into two phases: Screwing in and

tightening (impact mechanism in action). The impact mech-

anism is activated as soon as the screwed connection runs

tight and thus load is put on the motor. In this instance, the

impact mechanism converts the power of the motor to

steady rotary impacts. When loosening screws or nuts, the

process is reversed.

Starting Operation

Inserting the battery

Set the rotational direction switch (5) to the middle position

to avoid unintentionally switching it on. Insert the charged

battery (4) into the handle until you feel it engage and it is

flush with the handle.

Set the rotational direction (see figure C)

The rotational direction switch (5) is used to change the ro-

tational direction of the power tool. However, this is not pos-

sible while the on/off switch (6) is being pressed.

– Right rotation: To drive in screws and tighten nuts, press

the rotational direction switch (5) through to the left

stop.

– Left rotation: To loosen and unscrew screws and nuts,

press the rotational direction switch (5) through to the

right stop.

Switching on/off

To start the power tool, press and hold the on/off switch

(6).

English | 13

Bosch Power Tools 1 609 92A 49G | (07.09.2018)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PDR 18 LI Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info