Bedienungsanleitung Bosch PFS 2000 (Seite 20 von 303) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

766889

Zoom out

Zoom in

Vorherige Seite

1/303

Nächste Seite

20 | English

– Attach one strap end to each eyelet(28).

Changing the nozzle cap (PFS2000)

(seefigureC)

Note: Check the spray material by stirring it before selecting

the nozzle cap. Thin-viscosity material (e.g. wood paint) or

diluted material can be sprayed better with the grey nozzle

cap(9). Thick-viscosity material (e.g. wood lacquer or wall

paint) can be sprayed better with the white nozzle cap(10).

– To change the nozzle cap, unscrew the cap nut(3).

– Pull off the air cap(2) and the gasket(12).

– Unscrew the mounted nozzle cap.

When doing so, ensure that the O-ring(11) remains on

the nozzle cap.

– Screw the required nozzle cap into the thread in the spray

gun.

– Put the air cap(2) with the spacer(12) on the nozzle cap

and tighten it with the cap nut(3).

Operation

uPull the plug out of the socket before carrying out any

work on the power tool.

uProducts that are only sold in AUS and NZ: Use a resid-

ual current device (RCD) with a nominal residual current

of 30 mA or less.

Work preparation

uSpraying on the sides of water bodies (lakes, rivers,

etc.) or neighbouring surfaces in the direct catchment

area is not permitted.

uWhen purchasing paint, lacquer and spray material, pay

attention to their environmental compatibility.

Preparing the spray surface

The spray surface must be clean, dry and grease-free.

– Roughen smooth surfaces and then remove the sanding

dust.

When spraying, all non-covered surfaces can be contamin-

ated by the spray mist. Therefore, thoroughly prepare the

area around the surface to be sprayed:

– Carefully cover floors, furnishings, doors, windows as

well as door and window frames, etc. Painting substrate,

for example, is recommended for covering the floors.

– Fix the cover material in place. Cover material that is not

fixed in place securely can be detached or blown away by

the powerful air jet.

uCarefully mask off plug sockets and switches. Un-

covered plug sockets and switches may cause a short-cir-

cuit and increase the risk of electric shock.

Preparing the spray material

uWhen diluting, make sure that the spray material and

the diluting agent are compatible. When using a faulty

diluting agent, lumps can develop that can lead to clog-

ging of the spray gun.

uWhen diluting the spray material, make sure that the

flash point of the mixture is above 55°C again after di-

luting. Diluting substances such as solvent-based lac-

quers lowers the flash point.

uNote the specifications of the paint manufacturer re-

lating to sprayability, e.g. in the technical information

sheet or data sheet. Make sure that you do not spray

any paints that are not suitable according to the man-

ufacturer's specifications.

– Stir the spray material thoroughly.

Using spray material at room temperature will yield a bet-

ter spray pattern.

– Dilute the spray material if necessary.

If the spray test does not produce a good spray pattern,

dilute in 5% increments until an optimal spray pattern is

achieved.

Spray material Recommended dilu-

tion

Wood preservatives, water, oils,

thin glazes 0%

Impregnations, anti-rust primers 0−5%

Solvent-dilutable or water-dilutable

(recommended) lacquers, primers,

radiator lacquers, thick glazes

At least 5%

PFS2000: Emulsion paints and

latex paints (wall paints)

At least 10%

Dilution table

Spray mater-

ial

[ml]

Diluting agent [ml] for dilution

5% 10% 15%

300 15 30 45

400 20 40 60

500 25 50 75

600 30 60 90

Filling the spray material (seefiguresD1–D2)

Note: Remove the air hose(20) before pouring in spray ma-

terial (quarter turn of the bayonet lock(21) anticlockwise;

pull the bayonet lock (21) out of the port(4)).

– When using large buckets, pour the spray material into a

smaller transfer bucket(15) if necessary (e.g. 10l wall

paint into an empty 2.5 or 5.0l bucket).

– Unscrew the container(7) from the spray gun.

–PFS2000: If you are using already opened spray mater-

ial, place the thoroughly cleaned filling sieve(14) on the

container(7) to hold back any lumps of paint when pour-

ing in.

1 609 92A 687 | (16.09.2021) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PFS 2000 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info