Bedienungsanleitung Bosch PFS 2000 (Seite 21 von 303) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

766889

Zoom out

Zoom in

Vorherige Seite

1/303

Nächste Seite

English | 21

– Pour the spray material into the container(7) up to no

more than the 800 mark.

– Turn the suction tube(13) so that the spray material can

be sprayed with almost no residue:

For spray jobs on horizontal

surfaces/objects Towards the front in the dir-

ection of the nozzle/air cap

For spray jobs overhead Towards the rear in the dir-

ection of the handle

– Carry out a test-spray run on a test surface.

If the spray pattern is optimal, you can begin spraying.

If the spraying results are unsatisfactory or no paint is emit-

ted: (see "Troubleshooting", page24)

Starting Operation

uPay attention to the mains voltage. The voltage of the

power source must match the voltage specified on the

rating plate of the power tool.

uMake sure that the base unit cannot draw in dust or

other contamination during operation.

uMake sure never to spray on the base unit.

uStop spraying if fluid escapes from places other than

the intended nozzle during spraying, and restore the

spray gun to its proper condition. There is a risk of elec-

tric shock.

uDo not direct the fine-spray system against yourself,

other persons or animals.

Switching on (seefigureE)

–PFS2000: Check whether the correct nozzle cap is fit-

ted. (see "Changing the nozzle cap (PFS2000)

(seefigureC)", page20)

– Plug the mains plug into a plug socket.

– Grasp the spray gun by the handle and point it at the tar-

get area.

– Slide the on/off switch(23) forwards.

– Pull the trigger switch(6) on the spray gun.

Note: Air always flows out at the air cap(2) when the base

unit is switched on.

Switching Off

– Let go of the trigger switch(6) and slide the on/off

switch(23) backwards.

– Pull the mains plug from the plug socket.

Working Advice

Spraying (seefigureF)

Note: Pay attention to the wind direction when you are using

the power tool outdoors.

– Firstly, carry out a spray test and adjust the spray pattern

and the spray material volume according to the spray ma-

terial.

For adjustments, see the following sections.

– Make sure to hold the spray gun with a uniform clearance

of 20–25cm vertical to the object being sprayed.

– Begin the spraying procedure outside the target area.

– Move the spray gun evenly horizontally or vertically ac-

cording to the spray pattern configuration.

An even surface quality can be achieved when the spray

paths overlap by 4–5cm.

– When spraying horizontal objects or spraying overhead,

hold the spray gun at a slight angle and move back from

the sprayed surface.

Risk of tripping! Be aware of potential obstacles.

– Avoid interruptions when spraying the target area.

Guiding the spray gun evenly will provide uniform surface

quality.

A non-uniform spraying angle and distance will lead to heavy

formation of paint mist and consequently an uneven surface.

– End the spraying procedure outside the target area.

Never completely empty the container for the spray material

by spraying. If the suction tube is no longer immersed in the

spray material, the spray jet will be interrupted and this will

result in an inconsistent surface.

– After breaks or refilling the container(7), check the

nozzle cap(10)/(9) and the air cap(2) and clean them if

required.

– If the spray material settles on the air cap(2) or the

nozzle cap, clean the components with a suitable brush or

a damp cloth.

Adjusting the spray pattern

uNever actuate the trigger switch(6) while adjusting

the air cap(2).

– Turn the air cap(2) to the required position.

Air cap Spray jet pattern Application

Horizontal flat jet

for vertical working

direction

Bosch Power Tools 1 609 92A 687 | (16.09.2021)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PFS 2000 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info