Bedienungsanleitung Bosch pfs 280 e (Seite 12 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

382842

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Before any work on the machine itself, pull the

mains plug.

■ Vibrations occur while working that, with time, can

loosen the fit of the saw blade and the saw blade

guide or between the saw blade guide and the

machine. Check regularly for excessive play and

replace the complete saw blade immediately as

required.

Always clamp the workpiece.

When working, never hold with the hand or fingers in

the area of the saw blade.

The fingers of the guiding hand must always be behind

the limiting ridge 14 (see Figure on the fold-out

page).

■ Never take hold of the saw blade!

When not in use – also during pauses in the work

– always place the saw teeth protector 8 on the

saw blade.

■ The use of cooling fluids is not permitted.

■ Never saw in the direction of the body!

(see Figure on the fold-out page)

Switch on the machine and apply to the edge of the

piece to be worked. Do not start sawing on the

complete workpiece surface (see Figure on the

fold-out page).

Exact starting of a cut is possible with the aid of a

piece of scrap wood. Use the wood piece as a stop

placed on the cutting line and saw along the edge.

Free-Hand Cut-Off Sawing

Clamp on the cut-off saw blade and switch on the

machine.

Place the machine on the edge of the work piece. The

machine should be held at a steep angle to the work

piece (approx. 60°).

Danger of kick-back when the saw blade tip plunges

in! Observe correct sawing direction (see Figure on

the fold-out page)!

Take care that the saw blade tip exits into free space.

The cutting path must be free of obstacles both above

and below.

Start the sawing of profile strips on the edge, not on a

radius (see Figure on the fold-out page).

At the end of the cut, avoid pressure on the saw blade

to prevent splintering of the workpiece.

Then switch off the machine immediately.

Always switch off the machine and allow to

come to a stop before putting down.

Do not brake the saw blade to a stop by

applying side pressure after switching off.

The machine may not be used in conjunction

with commercially available mitre boxed.

The use of the cut-off table (optional accessory, Order

No.: 0 603 999 014) makes possible the stationary

operation of the machine for cut-off work.

In this manner, 90° cuts as well as mitre cuts of any

angle can be performed exactly on workpieces.

☞ For the application of the machine in

conjunction with the cut-off table, the cut-off

saw blade is to be used (see Figure on the

fold-out page).

Note: The instructions for mounting of the machine on

the cut-off table as well as a detailed description for

working with the saw and the cut-off table can be

found in the special operating instructions for the cut-

off table.

Before any work on the machine itself, pull the

mains plug.

For safe and proper working, always keep the

machine and the ventilation slots clean.

Clean the tool holder on the machine and the saw

blade guide after each use.

If the machine should happen to fail despite the care

taken in manufacture and testing, repair should be

carried out by an authorised customer services agent

for Bosch power tools.

For all correspondence and spare parts orders, always

include the 10 digit order number of the machine.

WARNING

Important instructions for connecting a new 3-

pin plug to the 2 wire cable.

The wires in the cable are coloured according to the

following code:

Do not connect the blue or brown wire to the earth

terminal of the plug.

Important: If the plug on the cable of this machine

must be replaced, dispose of the old plug to prevent

misuse.

Working Instructions

Cut-off Table

Maintenance and Cleaning

strain relief

live = brown

neutral = blue

To be fitted

by qualified

professionals only

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch pfs 280 e Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info