Bedienungsanleitung Bosch PFZ 500 E (Seite 16 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

110121

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

1 609 929 N70 | (22.1.08) Bosch Power Tools

16 | English

Operation

Starting Operation

f Observe correct mains voltage! The voltage

of the power source must agree with the

voltage specified on the nameplate of the

machine. Power tools marked with 230 V can

also be operated with 220 V.

Switching On and Off

To start the machine, first push the lock-off but-

ton for the On/Off switch 5 and then press the

On/Off switch 4 and keep it pressed.

To switch off the machine, release the On/Off

switch 4.

Controling the Stroke Rate

Increasing or reducing the pressure on the

On/Off switch 4 enables stepless stroke-rate

control of the switched-on machine.

The required stroke rate is dependent on the ma-

terial and the working conditions and can be de-

termined by a practical trial.

Reducing the stroke rate is recommended when

the saw blade engages in the material as well as

when sawing plastic and aluminium.

Working Advice

Tips

f When sawing light building materials, ob-

serve the statutory provisions and the rec-

ommendations of the material suppliers.

f Do not carry out pocket or plunge cuts with

the power tool. Danger of kickback.

Check wood, press boards, building materials,

etc. for foreign objects such as nails, screws or

similar, and remove them, if required.

When using suitable saw blades, wood with nails

can also be sawn.

Switch the machine on and guide it toward the

workpiece to be sawn. Hold the power tool firmly

with both hands, position the guide stop 2 onto

the workpiece surface and saw through the ma-

terial applying uniform supporting pressure and

feed.

For a quick and clean cut, move the power tool

back and forth as with a conventional hand saw.

(see figure C).

After finishing the working procedure, switch the

power tool off.

If the saw blade should jam, switch the machine

off immediately. Widen the gap somewhat with a

suitable tool and pull out the machine.

Flush Cuts (see figure D)

Using elastic bimetal saw blades, items still at-

tached to a wall (e. g. projecting building ele-

ments such as water pipes, etc.) can be sawn off

flush at the wall.

f Pay attention that the saw blade always ex-

tends beyond the diameter of the material

being worked. There is danger of kickback.

Position the saw blade directly against the wall

and apply some lateral pressure via the tool until

the footplate faces against the wall. Switch the

power tool on and saw through the workpiece,

applying constant lateral pressure.

Coolant/Lubricant

When sawing metal, coolant/lubricant should be

applied alongside cutting line because of the ma-

terial heating up.

Maintenance and Service

Maintenance and Cleaning

f Before any work on the machine itself, pull

the mains plug.

f For safe and proper working, always keep

the machine and ventilation slots clean.

Clean the saw blade holder preferably with com-

pressed air or a soft brush. Remove the saw

blade from the power tool for this. Ensure proper

operation of the saw blade holder by applying a

suitable lubricant.

Heavy contamination of the machine can lead to

malfunctions. Therefore, do not saw materials

that produce a lot of dust from below or over-

head.

OBJ_BUCH-105-002.book Page 16 Tuesday, January 22, 2008 1:30 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PFZ 500 E Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info