Bedienungsanleitung Bosch PFZ 700 PE (Seite 17 von 105) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

97440

Zoom out

Zoom in

Vorherige Seite

1/105

Nächste Seite

English | 17

Bosch Power Tools 1 609 929 N72 | (30.1.08)

Dust/Chip Extraction

f Dusts from materials such as lead-containing

coatings, some wood types, minerals and

metal can be harmful to one’s health. Touch-

ing or breathing-in the dusts can cause aller-

gic reactions and/or lead to respiratory infec-

tions of the user or bystanders.

Certain dusts, such as oak or beech dust, are

considered as carcinogenic, especially in con-

nection with wood-treatment additives (chro-

mate, wood preservative). Materials contain-

ing asbestos may only be worked by

specialists.

– Provide for good ventilation of the working

place.

– It is recommended to wear a P2 filter-class

respirator.

Observe the relevant regulations in your coun-

try for the materials to be worked.

Operation

Operating Modes

f Before any work on the machine itself, pull

the mains plug.

Orbital Action Settings

The four orbital action settings allow for optimal

adaptation of cutting speed, cutting capacity and

cutting pattern to the material being sawed.

The level of orbital action can be set with rotary

switch 7, even during operation.

Pivoting Footplate (see figure B)

Due to its movability, the adjustable footplate 2

adapts to the required angular position of the

surface.

Starting Operation

f Observe correct mains voltage! The voltage

of the power source must agree with the

voltage specified on the nameplate of the

machine. Power tools marked with 230 V can

also be operated with 220 V.

Switching On and Off

To start the machine, press the On/Off switch 5

and keep it depressed.

To lock the pressed On/Off switch 5, press the

lock-on button 6.

To switch off the machine, release the On/Off

switch 5 or when it is locked with the lock-on but-

ton 6, briefly press the On/Off switch 5 and then

release it.

Controlling/Presetting the Stroke Rate

Increasing or reducing the pressure on the

On/Off switch 5 enables stepless stroke-rate

control of the switched-on machine.

Light pressure on the On/Off switch 5 results in

a low stroke rate. Increasing the pressure also in-

creases the stroke rate.

When the On/Off switch 5 is locked, it is not pos-

sible to reduce the stroke rate.

With the thumbwheel for stroke rate preselec-

tion 4, the stroke rate can be preset and changed

during operation.

The required stroke rate is dependent on the ma-

terial and the working conditions and can be de-

termined by a practical trial.

Orbital action switched off (level 0):

For working thin or hard material such

as sheet metal or steel.

For achieving clean cutting edges.

Orbital action level I:

For working non-ferrous metals, hard-

wood, plastics or materials of medium

density.

Orbital action level II:

For working with soft materials such

as light building materials, insulation

material, etc.

Orbital action level III:

For working with soft materials such

as soft wood or tree wood.

OBJ_BUCH-648-001.book Page 17 Wednesday, January 30, 2008 8:54 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PFZ 700 PE Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info