Bedienungsanleitung Bosch PFZ 700 PE (Seite 18 von 105) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

97440

Zoom out

Zoom in

Vorherige Seite

1/105

Nächste Seite

1 609 929 N72 | (30.1.08) Bosch Power Tools

18 | English

Reducing the stroke rate is recommended when

the saw blade engages in the material as well as

when sawing plastic and aluminium.

After longer periods of work at low stroke rate,

the machine can heat up considerably. Remove

the saw blade from the machine and allow the

machine to cool down by running it for approx.

3 minutes at maximum stroke rate.

Working Advice

Tips

f When sawing light building materials, ob-

serve the statutory provisions and the rec-

ommendations of the material suppliers.

Note: Do not cover the ventilation slots under-

neath the tool holder with the hand.

Check wood, press boards, building materials,

etc. for foreign objects such as nails, screws or

similar, and remove them, if required.

Switch the machine on and guide it toward the

workpiece. Position the footplate 2 onto the sur-

face of the work and saw through the material ap-

plying uniform contact pressure and feed. After

completing the working procedure, switch the

machine off.

If the saw blade should jam, switch the machine

off immediately. Widen the gap somewhat with a

suitable tool and pull out the machine.

Plunge Cutting (see figures C–D)

f The plunge cutting procedure is only suita-

ble for treating soft materials such as wood,

plaster board or similar! Do not work metal

materials with the plunge cutting procedure!

Use only short saw blades for plunge cutting.

Place the machine with the edge of the footplate

2 onto the workpiece and switch on. For power

tools with stroke speed control, set the maxi-

mum stroke speed. Press the power tool firmly

against the workpiece and allow the saw blade to

slowly plunge into the workpiece.

As soon as the footplate 2 fully lays on the sur-

face of the workpiece, continue sawing alongside

the desired cutting line.

Flush Cuts (see figure E)

Using elastic bimetal saw blades, items still at-

tached to a wall (e. g. projecting building ele-

ments such as water pipes, etc.) can be sawn off

flush at the wall.

f Pay attention that the saw blade always ex-

tends beyond the diameter of the material

being worked. There is danger of kickback.

Position the saw blade directly against the wall

and apply some lateral pressure via the tool until

the footplate faces against the wall. Switch the

power tool on and saw through the workpiece,

applying constant lateral pressure.

Coolant/Lubricant

When sawing metal, coolant/lubricant should be

applied alongside cutting line because of the ma-

terial heating up.

Maintenance and Service

Maintenance and Cleaning

f Before any work on the machine itself, pull

the mains plug.

f For safe and proper working, always keep

the machine and ventilation slots clean.

Cleaning the Saw Blade Holder (see figure F)

Clean the saw blade holder preferably with com-

pressed air or a soft brush. Remove the saw

blade from the power tool for this. Ensure proper

operation of the saw blade holder by applying a

suitable lubricant.

Heavy contamination of the machine can lead to

malfunctions. Therefore, do not saw materials

that produce a lot of dust from below or over-

head.

If the machine should fail despite the care taken

in manufacturing and testing procedures, repair

should be carried out by an after-sales service

centre for Bosch power tools.

In all correspondence and spare parts order,

please always include the 10-digit article number

given on the type plate of the machine.

OBJ_BUCH-648-001.book Page 18 Wednesday, January 30, 2008 8:54 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PFZ 700 PE Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info