Bedienungsanleitung Bosch pks 55 a (Seite 18 von 101) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

383727

Zoom out

Zoom in

Vorherige Seite

1/101

Nächste Seite

18 | English

1 619 929 J64 | (22.2.12) Bosch Power Tools

Insert the dust/chip box 25 firmly into the chip ejector 16.

Empty the dust/chip box 25 in time to maintain optimum effi-

ciency.

To empty the dust/chip box 25, pull it off of the sawdust ejec-

tor 16. Press the slider 26 upward, turn the dust/chip box 25

aside and empty it.

Before reattaching, clean the connection sleeve of the dust/

chip box 25.

Operation

Operating Modes

f Before any work on the machine itself, pull the mains

plug.

Adjusting the Cutting Depth (see figure F)

f Adjust the cutting depth to the thickness of the work-

piece. Less than a full tooth of the blade teeth should be

visible below the workpiece.

Loosen the clamping lever 27. For a smaller cutting depth,

pull the saw away from the base plate 12; for a larger cutting

depth, push the saw toward the base plate 12. Adjust the de-

sired cutting depth at the cutting-depth scale. Tighten the

clamping lever 27 again.

Adjusting the Cutting Angle

Loosen the wing bolts 7 and 14. Tilt the saw sidewards. Ad-

just the desired measure on the scale 5. Tighten the wing

bolts 7 and 14 again.

Note: For bevel cuts, the cutting depth is smaller than the set-

ting indicated on the cutting-depth scale 28.

Cutting Marks (see figure G)

(PKS 55 A/PKS 66 A/PKS 66 AF)

The “CutControl” 9 viewing window, which folds out to the

front, is used for precise guiding of the circular saw alongside

the cutting line on the workpiece. The “CutControl” 9 viewing

window has a mark each for right-angled cuts and for 45°

cuts.

The 0° cutting mark (30) indicates the position of the saw

blade for right-angled cuts. The 45° cutting mark (29) indi-

cates the position of the saw blade for 45° cuts.

For precise cuts, position the circular saw against the work-

piece as shown in the figure. It is best to carry out a trial cut.

Cutting Marks (PKS 55)

The 0° cutting mark (30) indicates the position of the saw

blade for right-angled cuts. The 45° cutting mark (29) indi-

cates the position of the saw blade for 45° cuts.

For precise cuts, position the circular saw against the work-

piece as shown in the figure. It is best to carry out a trial cut.

Starting Operation

f Observe correct mains voltage! The voltage of the pow-

er source must agree with the voltage specified on the

nameplate of the machine. Power tools marked with

230 V can also be operated with 220 V.

Switching On and Off

To start the machine, first push the lock-off button for the

On/Off switch 1 and then press the On/Off switch 2 and keep

it pressed.

To switch off the machine, release the On/Off switch 2.

Note: For safety reasons, the On/Off switch 2 cannot be

locked; it must remain pressed during the entire operation.

When not using the power tool, switch it off in order to save

energy.

Working Advice

Protect saw blades against impact and shock.

Guide the machine evenly and with light feed in the cutting di-

rection. Excessive feed significantly reduces the service life of

the saw blade and can cause damage to the power tool.

Sawing performance and cutting quality depend essentially

on the condition and the tooth form of the saw blade. There-

fore, use only sharp saw blades that are suited for the material

to be worked.

Sawing Wood

The correct selection of the saw blade depends on the type

and quality of the wood and whether lengthway or crossway

cuts are required.

When cutting spruce lengthways, long spiral chips are

formed.

Beech and oak dusts are especially detrimental to health.

Therefore, work only with dust extraction.

3029

OBJ_BUCH-841-006.book Page 18 Wednesday, February 22, 2012 3:44 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch pks 55 a Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info