Bedienungsanleitung Bosch pks 55 a (Seite 19 von 101) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

383727

Zoom out

Zoom in

Vorherige Seite

1/101

Nächste Seite

English | 19

Bosch Power Tools 1 619 929 J64 | (22.2.12)

Sawing Non-ferrous Metals

Note: Use only a sharp saw blade that is suitable for non-fer-

rous metals. This ensures a clean cut and prevents blade bind-

ing.

Guide the switched on power tool against the workpiece and

carefully start the cut. Continue the cut with low feed and

without interruption.

When sawing profiles, always begin the cut from the narrow

side; when sawing U-profiles, never start the cut from the

open side. Support long profiles in order to avoid blade bind-

ing and kickback of the power tool.

Sawing with Parallel Guide (see figure H)

The parallel guide 10 enables exact cuts along a workpiece

edge and cutting strips of the same dimension.

Loosen wing bolt 8 and slide the scale of the parallel guide 10

through the guide in the base plate 12. Adjust the desired cut-

ting width as the scale setting at the respective cutting mark

30 or 29; see Section “Cutting Marks”. Tighten wing bolt 8

again.

Sawing with Guide Rail (see figures I–K)

The guide rail 31 is used to carry out straight cuts.

The adhesive coating prevents the guide rail from slipping and

protects the surface of the workpiece.

The guide rail 31 can be extended. For this, turn around both

guide rails 31 by 180° and connect both guide rails 31 by in-

serting them. Press button 32 to lock the guide rails. To disas-

semble the guide rails, press the opposite button 32 and pull

the guide rails 31 apart.

The guide rail 31 has two marks on the top side. The side with

the “90°” mark is used for right-angled cuts, and the side with

the “45°” mark is used for all other mitre cuts.

The rubber lip on the guide rail acts as a splinter guard for 90 °

and 45° cuts; it prevents fraying of the surface while sawing

wooden materials.

Upon initial sawing, the rubber lip is adapted to your circular

saw, and slightly cut off in this process.

Note: On the workpiece side where the cut is being started,

the guide rail 31 must always face flush against the work-

piece, and may not project beyond it.

Should the guide rail 31 project beyond the workpiece end,

do not rest the circular saw on the guide rail 31 without hold-

ing the circular saw. The guide rail 31 is made of plastic and

cannot hold the circular saw.

Fasten the guide rail 31 to the workpiece using the special

screw clamps 33. Take care that the cam on the inside of the

screw clamp 33 is seated in the corresponding recess of the

guide rail 31.

Switch the machine on and guide it in the cutting direction ap-

plying moderate and steady feed.

Maintenance and Service

Maintenance and Cleaning

f Before any work on the machine itself, pull the mains

plug.

f For safe and proper working, always keep the machine

and ventilation slots clean.

The retracting blade guard must always be able to move freely

and retract automatically. Therefore, always keep the area

around the retracting blade guard clean. Remove dust and

chips by blowing out with compressed air or with a brush.

Saw blades that are not coated can be protected against cor-

rosion with a thin coat of acid-free oil. Before use, the oil must

be removed again, otherwise the wood will become soiled.

Resin and glue residue on the saw blade produces poor cuts.

Therefore, clean the saw blade immediately after use.

If the replacement of the supply cord is necessary, this has to

be done by Bosch or an authorized Bosch service agent in or-

der to avoid a safety hazard.

If the machine should fail despite the care taken in manufac-

turing and testing procedures, repair should be carried out by

an after-sales service centre for Bosch power tools.

In all correspondence and spare parts order, please always in-

clude the 10-digit article number given on the type plate of

the machine.

After-sales Service and Customer Assistance

Our after-sales service responds to your questions concern-

ing maintenance and repair of your product as well as spare

parts. Exploded views and information on spare parts can al-

so be found under:

www.bosch-pt.com

Our customer service representatives can answer your ques-

tions concerning possible applications and adjustment of

products and accessories.

Great Britain

Robert Bosch Ltd. (B.S.C.)

P.O. Box 98

Broadwater Park

North Orbital Road

Denham

Uxbridge

UB 9 5HJ

Tel. Service: +44 (0844) 736 0109

Fax: +44 (0844) 736 0146

E-Mail: boschservicecentre@bosch.com

Ireland

Origo Ltd.

Unit 23 Magna Drive

Magna Business Park

City West

Dublin 24

Tel. Service: +353 (01) 4 66 67 00

Fax: +353 (01) 4 66 68 88

OBJ_BUCH-841-006.book Page 19 Wednesday, February 22, 2012 3:44 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch pks 55 a Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info