Bedienungsanleitung Bosch PLR 50 (Seite 20 von 128) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

504769

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

20 | English

2 609 140 621 | (18.7.11) Bosch Power Tools

Switching On and Off

To switch on the measuring tool, briefly press the On/Off button 7 or measuring

button 12. When switching on the measuring tool, the laser beam is not switched

on yet.

To switch off the measuring tool, press the On/Off button 7 for a few seconds.

If none of the measuring tool buttons are pressed for approx. 5 minutes, the

measuring tool switches off automatically in order to extend the service life of

the battery.

When a measured value has been stored, it is retained in automatic switch-off

mode. When switching on the measuring tool again, “M” is indicated in the dis-

play.

Measuring Procedure

After switching on, the measuring tool is in the length measurement mode. Other

measuring modes can be switched to by pressing the respective function/mode

button (see “Measuring Functions”, page 20).

After switching on, the rear edge of the measuring tool is preset as the reference

level for the measurement. To change the reference level, see “Selecting the Ref-

erence Level”, page 20.

Upon selection of the measuring function and the reference level, all further

steps are carried out by pushing the measuring button 12.

With the reference level selected, place the measuring tool against the desired

measuring line (e.g. a wall).

Push the measuring button 12 to switch on the laser beam.

f Do not point the laser beam at persons or animals and do not look into the

laser beam yourself, not even from a large distance.

Aim the laser beam at the target surface. Push the measuring button 12 again to

initiate the measurement.

In the tracking function, the measurement already starts upon first actuation of

the measuring button 12.

Typically, the measured value appears after 0.5 and latest after 4 seconds. The

duration of the measurement depends on the distance, the light conditions and

the reflection properties of the target surface. The end of the measurement is in-

dicated by a signal tone. The laser beam is switched off automatically upon com-

pletion of the measurement.

When no measurement has taken place approx. 20 seconds after sighting, the

laser beam is switched off automatically to save the batteries.

Selecting the Reference Level (see figures A–C)

For measuring, you can select between three different reference levels:

– The rear measuring-tool edge (e.g. when measuring onward from a wall),

– The rear positioning-pin edge 14 (e.g. when measuring from a corner),

– The front measuring-tool edge (e.g. when measuring onward from a table

edge).

To change the reference level, press button 9 until the requested reference level

is indicated on the display. Each time after switching on the measuring tool, the

rear end of the measuring tool is preset as the reference level.

Measuring Functions

Length Measurement

For length measurement, push button 1. The indicator for length measurement

appears in the display .

OBJ_DOKU-27449-001.fm Page 20 Monday, July 18, 2011 10:31 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PLR 50 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch PLR 50

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info