Bedienungsanleitung Bosch PLR 50 (Seite 22 von 128) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

504769

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

22 | English

2 609 140 621 | (18.7.11) Bosch Power Tools

Continuous Measurement (Tracking) (see figure E)

For continuous measurements, the measuring tool can be moved relative to the

target, whereby the measuring value is updated approx. every 0.5 seconds. In

this manner, as an example, you can move a certain distance away from a wall,

while the actual distance can always be read.

For continuous measurements, push button 6. The indicator for continuous

measurement (tracking) appears in the display .

Press the measuring button 12 to initiate the measur-

ing procedure. Move the measuring tool until the re-

quired distance value is indicated at the bottom of the

display.

Pushing the measuring button 12 interrupts the con-

tinuous measurement. The current measured value is

indicated in the display. Repeated pushing of the measuring button 12 starts the

continuous measuring again.

Continuous measurement automatically switches off after 5 min. The last meas-

ured value remains indicated on the display. To cancel continuous measure-

ment, you can change the measuring function by pressing button 1, 3 or 5.

Deleting Measured Values

Briefly pressing button 7 deletes the last individual measuring value determined

in all measuring functions. Briefly pressing the button repeatedly deletes the in-

dividual measured values in reverse order.

Memory Functions

When switching off the measuring tool, the value in the memory is retained.

Storing/Adding Measured Values

Push the memory add button 2 in order to store the

current measured value – a length, area or volume

value, depending on the current measuring function.

As soon as a value has been stored, “M” is indicated

in the display and the “+” behind it briefly flashes.

If a value is already stored in the memory, the new value is added to the memory

contents, however, only when the measures of unit correspond.

As an example, when an area value is in the memory and the current measured

value is a volume value, the addition cannot take place. “Error” briefly flashes in

the display.

Subtracting Measured Values

Push the memory subtraction button 8 in order to subtract the current measured

value from the memory value. As soon as a value has been subtracted, “M” is in-

dicated in the display and the “–” behind it briefly flashes.

If a value is already stored in the memory, the new measured value can be sub-

tracted only when the measures of unit correspond (see “Storing/Adding Meas-

ured Values”).

Displaying the Stored Value

Push the memory retrieve button 4 in order to display

the value stored in the memory. “M=” is indicated in

the display. When the memory contents “M=” is indi-

cated in the display, it can be doubled by pushing the

memory add button 2 or set to zero by pushing the

memory subtract button 8.

OBJ_DOKU-27449-001.fm Page 22 Monday, July 18, 2011 10:31 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PLR 50 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch PLR 50

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info