Bedienungsanleitung Bosch PMF 10,8 LI (Seite 25 von 152) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

460547

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

English | 25

Bosch Power Tools 2 609 004 157 | (11.5.10)

Sawing

f Use undamaged faultless saw blades only.

Deformed, blunt saw blades or saw blades

that are otherwise damaged can break.

f When sawing light building materials, ob-

serve the statutory provisions and the rec-

ommendations of the material suppliers.

f Plunge cuts may only be applied to soft ma-

terials, such as wood, gypsum plaster

boards, etc.!

Before sawing with HCS saw blades in wood,

particle board, building materials, etc., check

these for foreign objects such as nails, screws,

or similar. If required, remove foreign objects or

use BIM saw blades.

Separating

Note: When separating wall tiles take into con-

sideration that the application tools/accessories

wear heavily when used for longer periods of

time.

Sanding

The removal rate and the sanding pattern are

primarily determined by the choice of sanding

sheet, the preset oscillation rate and the ap-

plied pressure.

Only flawless sanding sheets achieve good

sanding capacity and extend the service life of

the machine.

Pay attention to apply uniform sanding pres-

sure; this increases the working life of the sand-

ing sheets.

Intensifiying the sanding pressure does not lead

to an increase of the sanding capacity, but to in-

creased wear of the machine and the sanding

sheet.

For precise on-the-spot sanding of edges, cor-

ners and hard to reach areas, it is also possible

to work only with the tip or an edge of the sand-

ing plate.

When selectively sanding on the spot, the sand-

ing sheet can heat up considerably. Reduce the

orbital stroke rate and allow the sanding sheet

to cool down regularly.

A sanding sheet that has been used for metal

should not be used for other materials.

Use only original Bosch sanding accessories.

To reduce the dust exposure and achieve better

working results when sanding, use dust extrac-

tion as far as possible.

Scraping

For scraping, select a high oscillation rate.

Work on a soft surface (e.g. wood) at a flat ange,

and apply only light pressure. Otherwise the

scraper can cut into the surface.

Temperature-dependent Overload Protection

When using the machine as intended for, it can-

not be subject to overload. In case of excessive

load or when not within the permitted battery

temperature range of –20 °C to +65 °C, the ma-

chine switches off. In case of overload, the bat-

tery charge-control indicator 4 will additionally

flash red for a few seconds.

After an automatic shut-off, switch the machine

off. Wait until the battery temperature is within

the allowable range before switching the ma-

chine on again.

Recommendations for Optimal Handling of the

Battery

Protect the battery against moisture and water.

Store the battery only within a temperature

range between 0 °C and 45 °C. As an example,

do not leave the battery in the car in summer.

A significantly reduced working period after

charging indicates that the battery is used and

must be replaced.

Observe the notes for disposal.

OBJ_BUCH-1170-002.book Page 25 Tuesday, May 11, 2010 3:36 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PMF 10,8 LI Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info