Bedienungsanleitung Bosch PMF 10,8 LI (Seite 23 von 152) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

460547

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

English | 23

Bosch Power Tools 2 609 004 157 | (11.5.10)

Selecting the Sanding Sheet

Depending on the material to be worked and the required rate of material removal, different sanding

sheets are available:

Dust/Chip Extraction

f Dusts from materials such as lead-containing

coatings, some wood types, minerals and

metal can be harmful to one’s health. Touch-

ing or breathing-in the dusts can cause aller-

gic reactions and/or lead to respiratory infec-

tions of the user or bystanders.

Certain dusts, such as oak or beech dust, are

considered as carcinogenic, especially in

connection with wood-treatment additives

(chromate, wood preservative). Materials

containing asbestos may only be worked by

specialists.

– Use dust extraction whenever possible.

– Provide for good ventilation of the work-

ing place.

– It is recommended to wear a P2 filter-

class respirator.

Observe the relevant regulations in your

country for the materials to be worked.

Connecting the Dust Extraction (see figure A)

Remove the application tool/accessory when

mounting the dust extraction 18 (accessory).

If required, assemble the parts of the dust extrac-

tion 18 as shown in the figure. Position the as-

sembled dust extraction onto the machine via the

tool holder 7. Turn the dust extraction in such a

manner that the cams of the dust extraction en-

gage into the corresponding recesses on the

housing. Fasten the dust extraction to the ma-

chine with the retaining clip 16 as shown in the

figure.

Pay attention that the felt ring 15 is undamaged

and faces tightly against the sanding plate 12.

Replace a damage felt ring immediately.

Place a vacuum hose 19 (accessory) onto the

vacuum connection 17. Connect the vacuum

hose 19 with a vacuum cleaner (accessory). An

overview for the connection of various vacuum

cleaners can be found at the end of these instruc-

tions.

The vacuum cleaner must be suitable for the ma-

terial being worked.

When vacuuming dry dust that is especially det-

rimental to health or carcinogenic, use a special

vacuum cleaner.

Sanding disc Material Application Grain size

Red quality

– All wooden materi-

als (e.g., hard-

wood, softwood,

chipboard, building

board)

– Metal materials

For coarse-sanding, e.g. of rough, un-

planed beams and boards

coarse 40

For face sanding and planing small

irregularities

medium 80

100

120

For finish and fine sanding of wood fine 180

240

320

400

White quality

–Paint

–Varnish

– Filling compound

– Filler

For sanding off paint coarse 40

For sanding primer (e.g., for removing

brush dashes, drops of paint and paint

run)

medium 80

100

120

For final sanding of primers before coat-

ing

fine 180

240

320

OBJ_BUCH-1170-002.book Page 23 Tuesday, May 11, 2010 3:36 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PMF 10,8 LI Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info