Bedienungsanleitung Bosch PMF 10,8 LI (Seite 21 von 152) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

460547

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

English | 21

Bosch Power Tools 2 609 004 157 | (11.5.10)

Assembly

Battery Charging

f Use only the battery chargers listed on the

accessories page. Only these battery charg-

ers are matched to the lithium ion battery of

your power tool.

Note: The battery is supplied partially charged.

To ensure full capacity of the battery, complete-

ly charge the battery in the battery charger be-

fore using your power tool for the first time.

The lithium ion battery can be charged at any

time without reducing its service life. Interrupt-

ing the charging procedure does not damage the

battery.

The battery is equipped with a NTC temperature

control which allows charging only within a tem-

perature range of between 0 °C and 45 °C. A long

battery service life is achieved in this manner.

Removing the Battery

To remove the battery 2, press the unlocking

buttons 1 and pull the battery out of the ma-

chine to the rear. Do not exert any force.

Battery Charge-control Indication

When the power tool is switched on, the battery

charge-control indicator 4 signals the still avail-

able battery capacity or an overload.

When the battery charge-control indicator 4

flashes red, the machine is subject to overload.

Please observe the information in section “Tem-

perature-dependent Overload Protection”,

page 25.

Changing the Tool

f Before any work on the machine itself (e.g.

maintenance, tool change, etc.) as well as

during transport and storage, remove the

battery from the power tool. There is danger

of injury when unintentionally actuating the

On/Off switch.

f Wear protective gloves when changing ap-

plication tools/accessories. Contact with

the application tool/accessoriy can lead to

injuries.

Selecting the Application Tool/Accessory

The following table shows examples for application tools. Further application tools can be found in

the extensive Bosch accessories program.

Indication Capacity

Continuous lighting, green >70 %

Continuous lighting, yellow 30–70 %

Continuous lighting, red <30 %

Accessory Material Application

BIM segment

saw blade

Wooden materials,

plastic, non-ferrous

metals

Separating and plunge cuts; also for sawing

close to edges, in corners and hard to reach

areas;

Example: shortening already installed bottom

rails or door hinges, plunge cuts for adjusting

floor panels

Base plate for

sanding, se-

ries Delta

93 mm

Depends on sand-

ing sheet

Sanding surfaces close to edges, in corners

or hard to reach areas;

Depending on the sanding sheet for, e.g.,

sanding wood, paint, varnish, stone

HCS plunge

cut saw blade,

wood

Wooden materials,

soft plastics

Separating and deep plunge cuts; also for

sawing close to edges, in corners and hard to

reach areas;

Example: narrow plunge cut in solid wood for

installing a ventilation grid

OBJ_BUCH-1170-002.book Page 21 Tuesday, May 11, 2010 3:36 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PMF 10,8 LI Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info