Bedienungsanleitung Bosch PMF 190 E (Seite 16 von 90) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

508454

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

16 | English

2 609 005 779 | (21.2.12) Bosch Power Tools

Dust/Chip Extraction

f Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suitable

for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

f Prevent dust accumulation at the workplace. Dusts can

easily ignite.

Connecting the Dust Extraction (see figure A)

The dust extraction 16 is intended only when working with the

sanding plate 9; it is not of use in combination with other ap-

plication tools.

For sanding, always connect the dust extraction.

To mount the dust extraction 16 (accessory), remove the ap-

plication tool and the depth stop 11.

Slide the dust extraction 16 over and beyond the tool holder

5 to the stop onto the gear head of the power tool. Insert fas-

tening screw 15 into the corresponding recess on the hous-

ing. To lock the screw, turn it to the position.

Pay attention that the felt ring 17 is undamaged and faces

tightly against the sanding plate 9. Replace a damage felt ring

immediately.

Place a vacuum hose 13 (accessory) onto the vacuum con-

nection 14. Connect the vacuum hose 13 with a vacuum

cleaner (accessory).

An overview for connecting to various vacuum cleaners can be

found on the graphics page.

The vacuum cleaner must be suitable for the material being

worked.

When vacuuming dry dust that is especially detrimental to

health or carcinogenic, use a special vacuum cleaner.

To remove the dust extraction 16, turn fastening screw 15 to

the position and pull the dust extraction from the gear

head of the power tool.

Operation

Starting Operation

f Observe the mains voltage! The voltage of the power

source must correspond with the data on the type plate of

the machine.

Switching On and Off

To start the machine, push the On/Off switch 1 forward so

that the “I” is indicated on the switch.

To switch off the machine, push the On/Off switch 1 toward

the rear so that the “0” is indicated on the switch.

When not using the power tool, switch it off in order to save

energy.

Preselecting the Orbital Stroke Rate

With the thumbwheel for preselection of the orbital stroke

rate 2, you can preselect the required orbital stroke rate, even

during operation.

The required stroke rate depends on the material and the

working conditions and can be determined through practical

testing.

When sawing, cutting and sanding harder materials, e.g.,

wood or metal, it is recommended to work with orbital stroke

rate “6”; for softer materials, such as plastic, orbital stroke

rate “4” is recommended.

Working Advice

f Wait until the machine has come to a standstill before

placing it down.

f Before any work on the machine itself, pull the mains

plug.

Note: Do not cover off the venting slots 3 of the machine while

working, as this reduces the working life of the machine.

While working with HCS tools make sure that the covering of

the tools is undamaged.

Operating Principle

Due to the oscillating drive the application tool/accessory

swings up to 21000 times per minute for 2.8° . This allows for

precise work in narrow spaces.

Work with low and uniform application

pressure, otherwise, the working perform-

ance will decline and the application tool

can become blocked.

While working, move the machine back and

forth, so that the application tool does not

heat up excessively and become blocked.

Sawing

f Use only undamaged saw blades that are in perfect con-

dition. Bent or dull saw blades can break, negatively influ-

ence the cut, or lead to kickback.

f When sawing light building materials, observe the stat-

utory provisions and the recommendations of the ma-

terial suppliers.

f Plunge cuts may only be applied to soft materials, such

as wood, gypsum plaster boards, etc.!

Before sawing with HCS saw blades in wood, particle board,

building materials, etc., check these for foreign objects such

as nails, screws, or similar. If required, remove foreign ob-

jects or use BIM saw blades.

Separating

Note: When separating wall tiles take into consideration that

the application tools/accessories wear heavily when used for

longer periods of time.

OBJ_BUCH-345-008.book Page 16 Tuesday, February 21, 2012 1:35 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PMF 190 E Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info