Bedienungsanleitung Bosch PMF 190 E (Seite 15 von 90) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

508454

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

English | 15

Bosch Power Tools 2 609 005 779 | (21.2.12)

Mounting/Replacing the Application Tool/Accessory

If required, remove an already mounted application tool/

accessory.

For removing the application tool/accessory loosen the screw

7 with the allen key 8 and remove the tool.

Mount the application tool/accessory (e.g. plunge cut saw

blade 6) in such a way on the tool holder 5 that the openings

of the tool engage into the cams of the tool holder.

For a safe and fatigue-free working position it is possible to

position the application tools/accessories in any snap-in posi-

tions on the tool holder. Position the tool in such a way that

the depressed centre points downwards (marking on the tool

is readable from above, see figure on the graphics page).

Use the screw 7 to fasten the application tool/accessory.

Tightly fasten the screw 7 with the allen key 8.

f Check the tight seating of the application tool/acces-

sory. Incorrect or not securely fastened application tools/

accessories can come loose during operation and pose a

hazard.

Mounting the Depth Stop

The depth stop 11 can be used when working with segment

saw blades, Riff-segment saw blades and segment blades.

If required, remove an already mounted application tool/

accessory.

Slide the depth stop 11 over and beyond the tool holder 5 to

the stop onto the gear head of the power tool with the labelled

side facing upward.

The depth stop is intended for the following cutting depths:

– With segment saw blades ACZ 85 .. with a diameter of

85 mm: 8 mm, 10 mm, 12 mm and 14 mm cutting depths

(see indication on the depth stop in large font and not in

brackets).

– With segment saw blades ACZ 100 .. with a diameter of

100 mm: 14 mm, 16 mm, 18 mm and 20 mm cutting

depths (see indication on the depth stop in smaller font

and brackets).

Mount the fitting segment saw blade for the desired cutting

depth. Turn the depth stop 11 in such a manner that the de-

sired cutting depth is above the section of the saw blade, with

which the cut is to be made.

For all other cutting depths and when working with other appli-

cation tools, remove the depth stop 11. For this, remove the

application tool and pull the depth stop from the gear head.

Mounting/Replacing a Sanding Sheet on the Sanding Plate

The sanding plate 9 is fitted with Velcro backing for quick and

easy fastening of sanding sheets with Velcro adhesion.

Before attaching the sanding sheet 10, free the Velcro back-

ing of the sanding plate 9 from any debris by tapping against

it in order to enable optimum adhesion.

Position the sanding sheet 10 flush alongside one edge of the

sanding plate 9, then lay the sanding sheet onto the sanding

plate and press firmly.

To ensure optimum dust extraction, pay attention that the

punched holes in the sanding sheet match with the holes in

the sanding plate.

To remove the sanding sheet 10, grasp it at one of the tips and

pull it off from the sanding plate 9.

You can use all sanding sheets, fleece pads/polishing cloth

pads of the Delta 93 mm series of Bosch accessory program.

Sanding accessories, such as fleece pads/polishing cloth

pads, are attached to the sanding plate in the same manner.

Selecting the Sanding Sheet

Depending on the material to be worked and the required rate of material removal, different sanding sheets are available:

Sanding disc Material Application Grain size

Red quality

– All wooden materials

(e.g., hardwood, soft-

wood, chipboard, build-

ing board)

– Metal materials

For coarse-sanding, e.g. of rough, unplaned beams

and boards

coarse 40

For face sanding and planing small irregularities

medium 80

100

120

For finish and fine sanding of wood

fine 180

240

320

400

White quality

–Paint

– Varnish

– Filling compound

– Filler

For sanding off paint

coarse 40

For sanding primer (e.g., for removing brush dashes,

drops of paint and paint run)

medium 80

100

120

For final sanding of primers before coating

fine 180

240

320

OBJ_BUCH-345-008.book Page 15 Tuesday, February 21, 2012 1:35 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PMF 190 E Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info