Bedienungsanleitung Bosch PMF 2000 CE Systeembox (Seite 20 von 123) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch)

766880

Zoom out

Zoom in

Vorherige Seite

1/123

Nächste Seite

20 | English

Sanding sheet Material Application Grit

For final sanding of primers prior to painting Fine 180

240

320

Attaching/changing the sanding sheet on the sanding

plate

The sanding plate(11) is fitted with a hook-and-loop fasten-

ing, allowing sanding sheets with a hook-and-loop backing to

be secured quickly and easily.

Tap the hook-and-loop fastening of the sanding plate(11)

before fitting the sanding sheet(12) to facilitate maximum

adhesion.

Position the sanding sheet(12) so that it is flush with one

side of the sanding plate(11), then place the sanding sheet

on the sanding plate and press it on firmly.

To ensure optimum dust extraction, make sure that the

punched holes in the sanding sheet are aligned with the

drilled holes in the sanding plate.

To remove the sanding sheet(12), take hold of it by an edge

and pull it away from the sanding plate(11).

You can use all sanding sheets, polishing and cleaning

fleeces from the Delta 93mm series in the Bosch range of

accessories.

Sanding accessories such as fleece/polishing felt are at-

tached to the sanding plate in the same way.

Dust/Chip Extraction

The dust from materials such as lead paint, some types of

wood, minerals and metal can be harmful to human health.

Touching or breathing in this dust can trigger allergic reac-

tions and/or cause respiratory illnesses in the user or in

people in the near vicinity.

Certain dusts, such as oak or beech dust, are classified as

carcinogenic, especially in conjunction with wood treatment

additives (chromate, wood preservative). Materials contain-

ing asbestos may only be machined by specialists.

– Use a dust extraction system that is suitable for the ma-

terial wherever possible.

– Provide good ventilation at the workplace.

– It is advisable to wear a P2 filter class breathing mask.

The regulations on the material being machined that apply in

the country of use must be observed.

uAvoid dust accumulation at the workplace. Dust can

easily ignite.

Connecting the dust extraction system (see figure C)

The dust extraction system (17) is only designed for use

with the sanding plate (11); it serves no purpose when used

together with other application tools.

Always connect a dust extraction system for sanding.

Remove the application tool and the depth stop (13) for fit-

ting the dust extraction system (17) (accessory).

Slide the dust extraction system (17) as far as it will go over

the tool holder (6) onto the collar of the power tool. Turn the

dust extraction system to the required position (not directly

under the power tool). Push the clamping lever (15) shut to

fix the dust extraction system in position.

Plug the tool sleeve of the extraction hose (18) onto the ex-

traction outlet (16). Connect the dust extraction hose (18)

to a dust extractor (accessory).

You will find an overview of how to connect various dust ex-

tractors at the end of these operating instructions.

The dust extractor must be suitable for the material being

worked.

When extracting dry dust that is especially detrimental to

health or carcinogenic, use a special dust extractor.

Operation

Starting Operation

uPay attention to the mains voltage. The voltage of the

power source must match the voltage specified on the

rating plate of the power tool.

uProducts that are only sold in AUS and NZ: Use a resid-

ual current device (RCD) with a nominal residual current

of 30 mA or less.

Switching On/Off

uMake sure that you are able to press the On/Off switch

without releasing the handle.

To switch on the power tool, slide the on/off switch (1) for-

ward so that "I" appears on the switch.

The electronic soft start limits the torque when the power

tool is switched on and increases the service life of the mo-

tor.

The Constant Electronic keeps the orbital stroke rate at no

load and under load virtually consistent, guaranteeing uni-

form performance.

To switch off the power tool, slide the on/off switch (1)

backwards so that "0" appears on the switch.

Preselecting the orbital stroke rate

You can even preselect the required orbital stroke rate dur-

ing operation using the orbital stroke rate preselection

thumbwheel (2).

The required orbital stroke rate is dependent on the material

and the work conditions and can be determined using prac-

tical tests.

Orbital stroke rate level “6” is recommended for sawing, cut-

ting and sanding harder materials, such as wood or metal;

orbital stroke rate level “4” is recommended for softer ma-

terials, such as plastic.

Working Advice

uPull the plug out of the socket before carrying out any

work on the power tool.

1 609 92A 674 | (01.12.2020) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PMF 2000 CE Systeembox Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info