Bedienungsanleitung Bosch PMF 2000 CE Systeembox (Seite 19 von 123) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch)

766880

Zoom out

Zoom in

Vorherige Seite

1/123

Nächste Seite

English | 19

Application tool Material Application

HCS universal joint

cutter Expansion joints, window

putty, insulation materials

(rock wool)

Cutting soft materials;

example: Cutting silicone expansion joints or window

putty

Fitting/changing the application tool

(see figures A and B)

Remove the application tool if one has already been fitted.

To remove the application tool, use the hex key (10) to

loosen the clamping bolt(9) and remove the tool.

Position the required application tool (e.g. plunge cut saw

blade (8)) on the tool holder (6) so that the depressed

centre is facing downwards (see figure on the graphics page,

text on the application tool should be legible from above).

Turn the application tool to a position which is convenient

for the job at hand and allow it to lock into place in the cams

of the tool holder (6). Twelve positions offset by 30° are

possible for this.

The built-in magnet (7) holds the application tool in the re-

quired position in order to make it easier to mount.

Secure the application tool using the clamping bolt (9).

Tighten the clamping bolt using the hex key (10) until it is

flush with the application tool.

uCheck that the application tool is seated securely. Ap-

plication tools that are attached incorrectly or are not se-

curely fixed in place may come loose during operation,

thereby putting you at risk.

Fitting and Adjusting the Depth Stop

The depth stop (13) can be used when working with seg-

ment saw blades.

Remove the application tool if one has already been fitted.

Slide the depth stop (13) over the tool holder (6) and onto

the collar of the power tool as far as it will go, with the la-

belled side facing upwards.

The depth stop is intended for the following cutting depths:

– With segment saw blades ACZ85.. with a diameter of

85mm: Cutting depths 8mm, 10mm, 12mm and

14mm (information on the depth stop in a larger font size

and without brackets).

– With segment saw blades ACZ100.. with a diameter of

100mm: Cutting depths 14mm, 16mm, 18mm and

20mm (information on the depth stop in a smaller font

size and in brackets).

Insert the appropriate segment saw blade for the desired

cutting depth. Slide the depth stop (13) from the tool holder

(6) in the direction of the application tool until you can ro-

tate it freely. Rotate the depth stop (13) so that the desired

cutting depth is above the section of the saw blade that will

be used to saw. Slide the depth stop (13) onto the collar of

the power tool once again as far as it will go.

Remove the depth stop (13) for all other cutting depths and

for working with other application tools. To do this, remove

the application tool and pull the depth stop away from the

collar.

Fitting the Auxiliary Handle (accessory)

The low-vibration auxiliary handle enables the tool to be

used safely and more comfortably.

Screw the auxiliary handle into the thread (5) on the left or

right of the machine head depending on how you are work-

ing.

uDo not continue to use the power tool if the auxiliary

handle is damaged. Do not make any alterations to the

auxiliary handle.

Choosing the Sanding Sheet

Different sanding sheets are available, depending on the material you are working with and the required surface removal rate:

Sanding sheet Material Application Grit

Red quality

– All wood and wood-

based materials (e.g.

hardwood, softwood,

chipboard, construction

boards)

– Metal materials

For pre-sanding, e.g. of rough and uneven beams and

boards Coarse 40

For surface sanding and levelling of slight irregularities Medium 80

100

120

For finish-sanding and fine sanding of wood Fine 180

240

320

400

White quality

– Paint

– Varnish

– Filler

– Bodyfiller

For sanding down paint Coarse 40

For sanding undercoats (e.g. removing brushstrokes,

paint drips and paint runs) Medium 80

100

120

Bosch Power Tools 1 609 92A 674 | (01.12.2020)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PMF 2000 CE Systeembox Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info