Bedienungsanleitung Bosch POF 1200 AE (Seite 24 von 146) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

78174

Zoom out

Zoom in

Vorherige Seite

1/146

Nächste Seite

24 | English

1 609 929 S76 | (21.7.09) Bosch Power Tools

– Use dust extraction whenever possible.

– Provide for good ventilation of the work-

ing place.

– It is recommended to wear a P2 filter-

class respirator.

Observe the relevant regulations in your

country for the materials to be worked.

Mounting the Extraction Adapter

The extraction adapter 28 can be mounted with

the hose connection to the front or to the rear.

When mounting with the hose connection in

front, the chip shield 5 must be removed first.

Fasten the extraction adapter 28 with the two

knurled screws 29 to the base plate 6.

To ensure optimum extraction, the extraction

adapter 28 must be cleaned regularly.

Connecting the Dust Extraction

Insert an extraction hose (Ø 35 mm) 27 (acces-

sory) into the mounted extraction adapter. Con-

nect the extraction hose 27 to a vacuum cleaner

(accessory).

The machine can be plugged directly into the re-

ceptacle of a Bosch all-purpose vacuum cleaner

with remote starting control. The vacuum clean-

er starts automatically when the machine is

switched on.

The vacuum cleaner must be suitable for the ma-

terial being worked.

When vacuuming dry dust that is especially det-

rimental to health or carcinogenic, use a special

vacuum cleaner.

Mounting the Chip Shield (see figure C)

Insert the chip shield 5 from the front into the

guide in such a manner that it engages. To re-

move the chip shield, grasp it by the sides and

pull it off toward the front.

Operation

Starting Operation

f Observe correct mains voltage! The voltage

of the power source must agree with the

voltage specified on the nameplate of the

machine. Power tools marked with 230 V

can also be operated with 220 V.

Preselecting the Speed

The required speed can be preselected with the

thumbwheel 23 (also while running).

1 – 2 low speed

3 – 4 medium speed

5–6 high speed

The values shown in the chart are standard val-

ues. The necessary speed depends on the mate-

rial and the operating conditions, and can be de-

termined by practical testing.

Switching On and Off

Adjust the depth-of-cut before switching on or

off; see Section “Adjusting the Depth-of-cut”.

To start the machine, first push the lock-off but-

ton for the On/Off switch 1 and then press the

On/Off switch 22 and keep it pressed.

POF 1400 ACE: A lamp illuminates the routing

area.

To switch off the machine, release the On/Off

switch 22.

Material Router bit

diameter (mm)

Thumb-

wheel 23

Hardwood

(Beech)

4–10

12 – 20

22 – 40

5–6

3–4

1–2

Softwood (Pine) 4 – 10

12 – 20

22 – 40

5–6

3–6

1–3

Particle Board 4 – 10

12 – 20

22 – 40

3–6

2–4

1–3

Plastics 4 – 15

16 – 40

2–3

1–2

Aluminium 4 – 15

16 – 40

1–2

OBJ_BUCH-323-003.book Page 24 Tuesday, July 21, 2009 12:51 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch POF 1200 AE Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info