Bedienungsanleitung Bosch POF 1200 AE (Seite 26 von 146) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

78174

Zoom out

Zoom in

Vorherige Seite

1/146

Nächste Seite

26 | English

1 609 929 S76 | (21.7.09) Bosch Power Tools

–Turn the scale 17 to “0” and loosen wing bolt

11.

– Turn the adjustment knob 18 by 0.4 mm/4

graduation marks (difference from set to ac-

tual value) in clockwise direction and tighten

the wing bolt 11.

– Check the selected depth-of-cut by carrying

out another trial cut.

After adjusting the depth-of-cut, do not change

the position of the slide 12 on the depth stop 13

any more, so that the actual cutting depth can

be read on the scale 14.

Fine Adjustment of the Depth-of-cut

(POF 1200 AE)

Different depths-of-cut can be preset with the

step buffer 9. The adjustment is carried out in

the same manner as previously described, with

the difference that by screwing the adjusting

screws 24 in or out, the height difference be-

tween the stops can be changed.

Working Advice

f Protect router bits against shock and im-

pact.

Direction of Feed and Routing Process

(see figure E)

f The routing process must always be carried

out against the rotation direction of the

router bit 21 (up-cutting motion). When

routing in the direction with the rotation of

the router (down-cutting), the machine can

break loose, eliminating control by the user.

– Adjust the required depth-of-cut; see Section

“Adjusting the Depth-of-cut”.

– Place the machine with the router bit mount-

ed on the workpiece to be machined and

switch the power tool on.

– Push clamping lever 16 down and slowly low-

er the plunge router until the adjusted depth-

of-cut is reached. Let go of the clamping le-

ver 16 again to lock this plunge depth.

If required, push clamping lever 16 up again

to finally lock it in place.

– Carry out the routing process applying uni-

form feed.

– After finishing the cutting process, guide the

plunge router upward again to the upper-

most position.

– Switch the power tool off.

Routing with Auxiliary Guide (see figure F)

For working large workpieces, e. g. when rout-

ing grooves, a board or wood strip can be fas-

tened to the workpiece as an auxiliary guide

alongside which the router can be guided. Guide

the router with the flattened side of the guide

plate along the auxiliary guide.

Shaping or Molding Applications

For shaping or molding applications without the

use of a parallel guide, the router bit must be

equipped with a pilot or a ball bearing.

– Guide the switched on power tool from the

side toward the workpiece until the pilot or

the ball bearing of the router bit faces

against the workpiece edge to be machined.

– Guide the power tool alongside the work-

piece edge with both hands, paying attention

that the router is positioned rectangular. Too

much pressure can damage the edge of the

workpiece.

Routing with Parallel Guide (see figures G–H)

Slide the parallel guide 31 with the guide rods

30 into the base plate 6 and tighten it as re-

quired with the wing bolts 4.

Guide the switched on power tool with uniform

feed and lateral pressure on the parallel guide

alongside the workpiece edge.

Routing Circular Arc Profiles (see figures I – J)

Turn the parallel guide 31 around so that the

facing surface of the parallel guide faces up-

ward.

Slide the parallel guide 31 with the guide rods

30 into the base plate 6 and tighten it as re-

quired with the wing bolts 4.

Fasten the centring pin 32 with the wing bolt 33

through the hole in the parallel guide 31.

Pierce the centring pin 32 into the marked cen-

tre of the arc profile and carry out the routing

process applying uniform feed.

OBJ_BUCH-323-003.book Page 26 Tuesday, July 21, 2009 12:51 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch POF 1200 AE Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info