Bedienungsanleitung Bosch PRA3A6D70 (Seite 12 von 16) (Englisch)

746026

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

en Trouble shooting

3Trouble shooting

Tr oubl e s hoot i ng

Sometimes certain faults detected can be easily

resolved. Before calling the Technical Assistance

Service, bear in mind the following advice:

Fault Possible cause Remedial action

Electrical operation is gener-

ally impaired.

Defective circuit breaker. Check inside the fuse box to see if any of the fuses are

damaged. Replace if necessary.

The circuit breaker or one of the residual-current circuit

breakers has been triggered.

Check the control panel to see if the automatic circuit

breaker or a fault current switch has failed.

Automatic ignition is not work-

ing.

There may be remnants of food or cleaning agent resi-

dues trapped between the ignition plugs and the burners.

The spaces in between the ignition plugs and the burners

must be clean.

The burners are wet. Carefully dry the burner caps.

The burner caps have not been fitted correctly. Make sure that the caps have been fitted correctly.

The appliance is not earthed or has not been connected

correctly, or the earth cable is damaged.

Contact an electrician.

Automatic ignition is not work-

ing and the ”‚ or ”ƒ symbol

appears in the display.

The electronics have overheated. Switch the burners off or use only the lowest heat setting

until the electronics have cooled down sufficiently.

The burner flame is uneven. The burner parts have not been fitted correctly. Fit the burner parts to the relative burner correctly.

The burner slots are dirty. Clean the burner slots.

The gas does not appear to be

flowing correctly or there is no

gas being produced at all.

The gas supply has been shut off by the intermediate

valves.

Open the intermediate valves.

If gas is supplied by a gas cylinder, check that this is not

empty.

Replace the gas cylinder.

There is a smell of gas in the

kitchen.

The gas tap is open. Close the gas tap.

The gas cylinder has not been connected correctly. Make sure that the gas cylinder has been connected cor-

rectly.

Gas may be leaking. Close the central tap in the gas line, ventilate the room

and immediately call an authorised installer, who can

inspect the gas system and issue an installation certifi-

cate. Do not use the appliance until you are sure that gas

is not leaking from the system or the appliance.

The burner switches off as

soon as the control knob is

released.

The control knob was not held down for long enough. If the burner is switched on, hold the control knob down

for a few seconds longer.

The burner slots are dirty. Clean the burner slots.

”„, ”…, ”†, ”‡, ”ˆ, ”‰,

”Š appear in the display.

Electronics fault. Disconnect the hob from the power supply. Wait a few

seconds and then reconnect it. If the indicator remains lit,

contact the after-sales service.

The heat setting indicator in

the display continually devi-

ates from the heat setting that

was selected using the control

knob.

Incorrect calibration of the electronics. Carry out the calibration in accordance with the installa-

tion instructions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PRA3A6D70 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch PRA3A6D70

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info