Bedienungsanleitung Bosch PSB 1000-2 RCA (Seite 20 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

78649

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

20 | English 2 609 002 333 • 4.6.07

• After reaching the desired drilling depth, pull the

drill bit out of the drill hole first and then switch off

the impact drill.

• Check the condition of the filter element 21 regu-

larly. Replace a damaged filter element immediately.

• The dust protection ring 17 can wear, especially

when working with large drill-bit diameters. Replace

the dust protection ring when worn/damaged.

Mounting the Extraction Device (see figure A)

Depending on the desired working manner, tilt the

adapter 18 rightwards (right-hand operation) or left-

wards (left-hand operation) to the stop and slide the tel-

escopic guide 14 into the corresponding holder of the

auxiliary handle 12.

Loosen the wing bolt 19 and place the auxiliary handle

12 with the mounted extraction device onto the spindle

collar of the impact drill in such a manner that the

adapter 18 engages into the corresponding opening

below the keyless chuck. Tighten the wing bolt 19.

Cleaning the Extraction Device (see figure B)

Slide the locking latch 20 upward or empty the dust

collector 16 before placing down the extraction device.

The dust collector 16 is sufficient for approx. 40 drill-

ings with a drilling diameter of 6 mm.

When the extraction starts to get weaker or when the

dust collector 16 is about half full, the dust collector 16

must be emptied. For this, push the release buttons 15

and remove the dust collector 16.

Pull the filter element 21 from the dust collector 16

downward. Empty and clean the dust collector 16.

Clean the filter element 21 by striking or tapping out the

dust.

Check the filter element 21 for damage and replace it

as required.

Firstly, place the filter element 21 into the dust collector

16 and then insert the dust collector 16 into the bottom

of the extraction device, then swivel the dust collector

upward until it latches at the top.

Removing the Extraction Device

Loosen the wing bolt 19 and pull the auxiliary handle 12

with the mounted extraction device from the spindle

collar of the impact drill.

Tilt the adapter 18 to the stop and pull the telescopic

guide 14 out of the auxiliary handle 12

Auxiliary Handle (models with dust

extraction)

f Always use the power tool with the auxiliary

handle 12 provided.

The auxiliary handle 12 can be used with or without the

mounted extraction device. The auxiliary handle 12 can

be fastened in two different positions, see Chapter

“Mounting the Extraction Device”.

Adjusting the Drilling Depth (see figure C)

With the extraction device mounted, the drilling depth

“X” can be adjusted.

Insert a drill bit into the drill chuck and clamp the drill bit

as described in Chapter “Changing the Tool”. Rotate

the set collar for the depth stop 13 downward until it

can be moved alongside the telescopic guide 14. Place

the machine, without switching it on, firmly against the

edge of the surface to be drilled until the drill bit pro-

trudes out of the extraction device by the length of the

required drilling depth “X”. Slide the set collar for the

depth stop 13 until it faces against the auxiliary handle

12 and rotate the set collar upward in order to lock the

determined distance.

Auxiliary Handle (models without dust

extraction) (see figures D–E)

f Operate your machine only with the auxiliary

handle 23.

The auxiliary handle 23 can be set to any position for a

secure and low-fatigue working posture.

PSB 700-2 RE (see figure D)

Turn the wing bolt for adjustment of the auxiliary

handle 19 in anticlockwise direction and set the auxil-

iary handle 23 to the required position. Then tighten the

wing bolt 19 again in clockwise direction.

PSB 780-2 RE/PSB 1000-2 RCE (see figure E)

Turn the bottom part of the auxiliary handle 23 in coun-

terclockwise direction and swivel the auxiliary handle

23 to the desired position. Then retighten the bottom

part of the auxiliary handle 23 by turning in clockwise

direction.

Adjusting the Drilling Depth (see figures D–E)

The required drilling depth X can be set with the depth

stop 24.

Press the button for the depth stop adjustment 22 and

insert the depth stop into the auxiliary handle 23.

The knurled surface of the depth stop 24 must face

upward.

Pull out the depth stop until the distance between the

tip of the drill bit and the tip of the depth stop corre-

spond with the desired drilling depth X.

Changing the Tool

f Before any work on the machine itself, pull

the mains plug.

Keyless Chuck

(PSB 1000-2 RCE/PSB 1000-2 RCA/

PSB 800-2 RA/PSB 780-2 RE) (see figure F)

The drill spindle is locked when the On/Off switch 9 is

not pressed. This makes quick, convenient and easy

changing of the tool in the drill chuck possible.

OBJ_BUCH-79-006.book Page 20 Monday, June 4, 2007 4:08 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PSB 1000-2 RCA Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info