Bedienungsanleitung Bosch PSB 1000-2 RCA (Seite 21 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

78649

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

English | 212 609 002 333 • 4.6.07

Open the keyless chuck 1 by turning in rotation direc-

tion n, until the tool can be inserted. Insert the tool.

Firmly tighten the collar of the keyless chuck 1 by hand

in rotation direction o until the locking action (“click”)

is no longer heard. This automatically locks the chuck.

The locking is released again to remove the tool when

the collar is turned in the opposite direction.

Keyless Chuck (PSB 700-2 RE) (see figure G)

Hold the rear sleeve 26 of the keyless chuck 1 tight and

turn the front sleeve 25 in rotation direction n, until the

tool can be inserted. Insert the tool.

Hold the rear sleeve 26 of the keyless chuck 1 tight and

firmly turn the front sleeve 25 in rotation direction o by

hand until the locking action is no longer heard. This

automatically locks the drill chuck.

The locking is released again to remove the tool when

the front sleeve 25 is turned in the opposite direction.

Screwdriver Tools (see figures H–I)

When working with screwdriver bits 27, a universal bit

holder 28 should always be used. Use only screwdriver

bits that fit the screw head.

For driving screws, always position the “Drilling/Impact

Drilling” selector switch 2 to the “Drilling” symbol.

Replacing the Drill Chuck

f Before any work on the machine itself, pull

the mains plug.

Removing the Drill Chuck (see figure J)

Disassemble the auxiliary handle and set the gear

selector 11 to the centre position between the 1st and

2nd gear.

Insert a steel pin with a diameter of Ø 4 mm and

approx. 50 mm of length into the drill hole on the spin-

dle neck in order to lock the drill spindle.

Clamp the short end of an Allen key 29 into the keyless

chuck 1.

Place the machine on a stable surface (e.g. a work-

bench). Hold the machine firmly and loosen the keyless

chuck 1 by turning the Allen key 29 in rotation direction

n. Loosen a tight-seated keyless chuck by giving the

long end of the Allen key 29 a light blow. Remove the

Allen key from the keyless chuck and completely

unscrew the keyless chuck.

Mounting the Drill Chuck (see figure K)

The keyless chuck is mounted in reverse order.

Remove the steel pin from the drill hole on the

spindle neck after mounting is completed.

The drill chuck must be tightened with a

tightening torque of approx. 50–55 Nm.

Operation

Starting Operation

f Observe correct mains voltage! The voltage of

the power source must agree with the voltage

specified on the nameplate of the machine.

Power tools marked with 230 V can also be

operated with 220 V.

Stand by Indicator (PSB 1000-2 RCE/

PSB 1000-2 RCA)

The stand by indicator 5 lights up when the mains plug

is plugged in and mains voltage is available. When the

machine cannot be started even though the stand by

indicator is lit, it must be taken to an authorized after-

sales service agent for Bosch power tools.

Reversing the Rotational Direction (see figure L)

The rotational direction switch 10 is used to reverse the

rotational direction of the machine. However, this is not

possible with the On/Off switch 9 actuated.

Right rotation: Press the rotational direction switch

10 through to the right stop (for drilling and driving

screws).

PSB 1000-2 RCE/PSB 1000-2 RCA: The indicator

for right-hand rotation 3 lights up.

PSB 700-2 RE/PSB 780-2 RE/PSB 800-2 RA: The

indicator for right-hand rotation 31 indicates the

selected rotational direction.

Left rotation: Press the rotational direction switch 10

through to the left stop (for loosening and unscrewing

screws and nuts).

PSB 1000-2 RCE/PSB 1000-2 RCA: The indicator

for left-hand rotation 4 lights up.

PSB 700-2 RE/PSB 780-2 RE/PSB 800-2 RA: The

indicator for left-hand rotation 32 indicates the selected

rotational direction.

Setting the Operating Mode

Drilling and Screwdriving

Set the selector switch 2 to the “Drilling”

symbol.

Impact Drilling

Set the selector switch 2 to the “Impact drill-

ing” symbol.

The selector switch 2 engages noticeably and can also

be actuated with the machine running.

Switching On and Off

To start the machine, press the On/Off switch 9 and

keep it depressed.

To lock the pressed On/Off switch 9, press the lock-

on button 8.

OBJ_BUCH-79-006.book Page 21 Monday, June 4, 2007 4:08 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PSB 1000-2 RCA Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info