Bedienungsanleitung Bosch psb 7000 re (Seite 31 von 37) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

387161

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

English

NOTE: The recharging time may vary according to the

ambient temperature.

3. Disconnect the charger’s power cord from the

receptacle.

4. Hold the charger firmly and pull out the battery.

NOTE

Be sure to pull out the battery from the charger after

use, and then keep it.

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an extended

period is not activated, the electric discharge might

be low when using them the first and second time.

This is a temporary phenomenon, and normal time

required for recharging will be restored by recharging

the batteries 2 – 3 times.

How to make the batteries perform longer

(1) Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the battery

and recharge it after it has cooled for a while.

CAUTION:

⅜ When the battery charger has been continuously used,

the battery charger will be heated, thus constituting

the cause of the failures. Once the charging has been

completed, give 15 minutes rest until the next

charging.

⅜ If the battery charger does not work while the battery

is mounted correctly, it is probable that the battery or

charger is malfunctioning. Take it to your authorized

Service Center.

PRIOR TO OPERATION

1. Setting up and checking the work environment

Check if the work environment is suitable by following

the precautions.

HOW TO USE

How to make the batteries perform longer

⅜ Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

1. Installing the bit

Always follow the following procedure to install driver

bit. (Fig. 4)

(1) Pull the guide sleeve forward.

(2) Insert the bit into the hexagonal hole in the socket.

(3) Release the guide sleeve and it returns to its original

position.

CAUTION:

If the guide sleeve does not return to its original

position, then the bit is not installed properly.

2. Removing the bit

Please do the opposite point on the method of

installing bit.

3. Automatic spindle-lock mechanism

When the main switch is off, the bit is locked in place,

and the tool can be used as a manual screwdriver.

4. Confirm that the battery is mounted correctly

5. Confirm the clutch dial position (See Fig. 5)

The tightening torque of this unit can be adjusted

according to the clutch dial position, at which the

clutch dial is set.

(1) When using this unit as a screwdriver, line up the one

of the numbers “1, 5, 9 ... 21” on the clutch dial, or the

black dots, with the triangle mark on the outer body.

(2) When using this unit as a drill, align the clutch dial

drill mark “

” with the triangle mark on the outer

body.

CAUTION

⅜ The clutch dial cannot be set between the numerals

“1, 5, 9 ... 21” or the black dots.

⅜ Do not use with the clutch dial numeral between

“21” and the black line at the middle of the drill mark.

Doing so may cause damage (See Fig. 6).

6. Tightening torque adjustment

(1) Tightening torque

Tightening torque should correspond in its intensity

to the screw diameter. When too strong torque is

used, the screw head may be broken or be injured.

Be sure to adjust the clutch dial position according to

the screw diameter.

(2) Tightening torque indication (See Fig. 5)

The tightening torque differs depending on the type

of screw and the material being tightened.

The unit indicates the tightening torque with the

numbers “1, 5, 9 ... 21” on the clutch dial, and a black

dots. The tightening toque at position “1” is the

weakest and the torque is strongest at the highest

number.

(3) Adjusting the tightening torque (See Fig. 5)

Rotate the clutch dial and line up the numbers “1, 5, 9

... 21” on the clutch dial, or the dots, with the triangle

mark on the outer body. Adjust the clutch dial in the

weak or the strong torque direction according to the

torque you need.

Table 1 Recharging time (approx. min.) at 20°C

Battery

voltage

(V)

Battery capacity (Ah)

1.5 Ah

10.8 V BCL1015 40 min.

05Eng_DB10DL_NE 10/11/07, 7:01 PM30

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch psb 7000 re Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info