Bedienungsanleitung Bosch psb 7000 re (Seite 32 von 37) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

387161

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

English

CAUTION

⅜ The motor rotation may be locked to cease while the

unit is used as drill. While operating the driver drill,

take care not to lock the motor.

⅜ If the motor is locked, immediately turn the power

off. If the motor is locked for a while, the motor or

battery may be burnt.

⅜ Too long hammering may cause the screw broken

due to excessive tightening.

7. Check the rotational direction

The bit rotates clockwise (viewed from the rear side)

by pushing the R-side of the selector button.

The L-side of the selector button is pushed to turn the

bit counterclockwise (See Fig. 7) (The

and

marks are provided on the body).

8. Switch operation

⅜ When the trigger switch is depressed, the tool rotates.

When the trigger is released, the tool stops.

⅜ The rotational speed of the drill can be controlled by

varying the amount that the trigger switch is pulled.

Speed is low when the trigger switch is pulled slightly

and increases as the trigger switch is pulled more.

NOTE

⅜ A buzzing noise is produced when the motor is about

to rotate; This is only a noise, not a machine failure.

9. Using the light

Pull the trigger switch to light up the light. The light

keeps on lighting while the trigger switch is being

pulled. The light goes out after releasing the trigger

switch. (Fig. 8)

CAUTION:

Do not look directly into the light. Such actions could

result in eye injury.

10. The scope and suggestions for uses

The usable scope for various types of work based on

the mechanical structure of this unit is shown in

Table 2.

CAUTION:

⅜ The selection examples shown in Table 3 should be

considered as general standard. As different types of

tightening screws and different materials to be

tightened are used in actual works proper adjustments

are naturally necessary.

NOTE:

The use of the battery BCL1015 in a cold condition

(below 0 degree Centigrade) can sometimes result in

the weakened tightening torque and reduced amount

of work. This, however, is a temporary phenomenon,

and returns to normal when the battery warms up.

12. Battery level warning lamp

The battery level can be checked by pulling the trigger

switch while the power tool is in a no-load state. The

battery level warning lamp lights when the battery

power is very low. If this happens, charge the battery.

(Fig. 9)

NOTE:

⅜ The level at which the battery level warning lamp

lights may vary due to the ambient temperature,

characteristics of the battery, etc. and is intended

only as a guide.

⅜ The battery level warning lamp may light when the

power tool is overloaded. This does not mean that

the battery power is very low.

Be sure to check the battery level while the tool is in a

no-load state.

MAINTENANCE AND INSPECTION

1. Inspecting the tool

Since use of as dull tool will degrade efficiency and

cause possible motor malfunction, sharpen or replace

the tool as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so could result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Cleaning on the outside

When the driver drill is stained, wipe with a soft dry

cloth or a cloth moistened with soapy water. Do not

use chloric solvents, gasoline or paint thinner, for

they melt plastics.

5. Storage

Store the driver drill in a place in which the

temperature is less than 40°C and out of reach of

children.

6. Service parts list

CAUTION:

Repair, modification and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

Use Clutch dial position

Machine screw 1 – 21

Driving

Wood screw

1 –

Drilling

Wood

Work Suggestions

Drilling Wood Use for drilling purpose.

Machine screw Use the bit or socket matching the screw diameter.

Driving

Wood screw Use after drilling a pilot hole.

Table 2

11. How to select tightening torque

Table 3

05Eng_DB10DL_NE 10/11/07, 7:01 PM31

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch psb 7000 re Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info