Bedienungsanleitung Bosch PSR 1800 LI 2 SystemBox (Seite 15 von 191) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

765859

Zoom out

Zoom in

Vorherige Seite

1/191

Nächste Seite

English | 15

Operation

Starting Operation

Inserting the battery

Note: The use of batteries unsuitable for your power tool can

lead to malfunctions or damage to the power tool.

Set the rotational direction switch (11) to the middle posi-

tion to avoid unintentionally switching it on. Insert the

charged battery (8) into the handle until you feel it engage

and it is flush with the handle.

Set the rotational direction (see figureC)

The rotational direction switch (11) is used to change the ro-

tational direction of the power tool. However, this is not pos-

sible while the on/off switch (12) is being pressed.

Right rotation: To drill and to drive in screws, press the ro-

tational direction switch (11) through to the left stop.

The rotational direction indicator for right rotation

(5) lights up when the on/off switch (12) is

pressed and the motor is running.

Left Rotation: To loosen and unscrew screws and nuts,

press the rotational direction switch (11) through to the

right stop.

The rotational direction indicator for left rotation

(6) lights up when the on/off switch (12) is

pressed and the motor is running.

Preselecting the Torque

The torque presetting ring (3) can be used to preselect the

required torque in 20 stages. When the correct setting is

used, the application tool will be stopped when the screw is

driven flush into the material or once the set torque has been

reached. In position the overload clutch is deactivated,

e.g. for drilling.

When unscrewing screws, you can select a higher setting or

set the tool to the symbol.

Mechanical gear selection

uOnly operate the gear selector (4) when the power

tool is not in use.

You can preselect two speed ranges with the gear selector

(4).

Gear I:

Low speed range; for screwdriving or working with a large

drilling diameter.

Gear II:

High speed range; for working with a small drilling diameter.

If the gear selector switch (4) cannot be pushed all the way,

turn the tool holder (1) with the application tool slightly.

Temperature-dependent overload protection

In normal conditions of use, the power tool cannot be over-

loaded. If the power tool is overloaded or the permitted bat-

tery temperature is exceeded, the electronics of the power

tool will switch off until the temperature returns to within the

optimum operating temperature range.

Switching on/off

To start the power tool, press and hold the on/off switch

(12).

The lamp (9) lights up when the on/off switch (12) is lightly

or fully pressed, meaning that the work area is illuminated in

poor lighting conditions.

To switch off the power tool, release the on/off switch (12).

Adjusting the Speed

You can adjust the speed of the power tool when it is on by

pressing in the on/off switch (12) to varying extents.

A light pressure on the on/off switch (12) results in a low ro-

tational speed. Increased pressure on the switch causes an

increase in speed.

Practical advice

uOnly apply the power tool to the screw/nut when the

tool is switched off. Rotating tool inserts can slip off.

After working at a low speed for an extended period, you

should operate the power tool at the maximum speed for ap-

proximately three minutes without load to cool it down.

Maintenance and Service

Maintenance and Cleaning

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

uTo ensure safe and efficient operation, always keep

the power tool and the ventilation slots clean.

Clean the application tool, the tool holder, the power tool’s

ventilations slots, and the battery’s ventilation slots each

time after using.

After-Sales Service and Application Service

Our after-sales service responds to your questions concern-

ing maintenance and repair of your product as well as spare

parts. You can find explosion drawings and information on

spare parts at: www.bosch-pt.com

The Bosch product use advice team will be happy to help you

with any questions about our products and their accessor-

ies.

In all correspondence and spare parts orders, please always

include the 10‑digit article number given on the nameplate

of the product.

Great Britain

Robert Bosch Ltd. (B.S.C.)

P.O. Box 98

Broadwater Park

North Orbital Road

Denham Uxbridge

UB 9 5HJ

At www.bosch-pt.co.uk you can order spare parts or arrange

the collection of a product in need of servicing or repair.

Bosch Power Tools 1 609 92A 6DG | (07.06.2021)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PSR 1800 LI 2 SystemBox Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info