Bedienungsanleitung Bosch PWS 750-125 (Seite 28 von 167) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

78344

Zoom out

Zoom in

Vorherige Seite

1/167

Nächste Seite

28 | English

1 609 929 R16 | (28.9.09) Bosch Power Tools

To switch off the power tool, release the On/Off

switch 3 or, if it is locked, briefly push down the

back of the On/Off switch 3 and then release it.

f Check grinding tools before using. The

grinding tool must be mounted properly

and be able to move freely. Carry out a test

run for at least one minute with no load. Do

not use damaged, out-of-centre or vibrating

grinding tools. Damaged grinding tools can

burst and cause injuries.

Working Advice

f Exercise caution when cutting slots in

structural walls; see Section “Information

on Structures ”.

f Clamp the workpiece if it does not remain

stationary due to its own weight.

f Do not strain the machine so heavily that it

comes to a standstill.

f After heavily straining the power tool, con-

tinue to run it at no-load for several minutes

to cool down the cutting/grinding tool.

f Grinding and cutting discs become very hot

while working; do not touch until they have

cooled.

f Do not use the power tool with a cut-off

stand.

Rough Grinding

f Never use a cutting disc for roughing.

The best roughing results are achieved when

setting the machine at an angle of 30° to 40°.

Move the machine back and forth with moderate

pressure. In this manner, the workpiece will not

become too hot, does not discolour and no

grooves are formed.

Flap Disc

With the flap disc (accessory), curved surfaces

and profiles can be worked.

Flap discs have a considerably higher service

life, lower noise levels and lower sanding tem-

peratures than conventional sanding sheets.

Cutting Metal

f For cutting metal, always work with the pro-

tection guard for cutting 7.

When cutting, work with moderate feed, adapt-

ed to the material being cut. Do not exert pres-

sure onto the cutting disc, tilt or oscillate the

machine.

Do not reduce the speed of running down cut-

ting discs by applying sideward pressure.

The machine must

always work in an

up-grinding mo-

tion. Otherwise,

the danger exists

of it being pushed

uncontrolled out

of the cut.

When cutting pro-

files and square

bar, it is best to

start at the small-

est cross section.

Cutting Stone

f For cutting stone, always work with the cut-

ting guide with dust extraction protection

guard 16.

f The machine may be used only for dry cut-

ting/grinding.

For cutting stone, it is best to use a diamond

cutting disc. As a safety measure against jam-

ming, the cutting guide with dust extraction pro-

tection guard 16 must be used.

Operate the machine only with dust extraction

and additionally wear a dust protection mask.

The vacuum cleaner must be approved for the

extraction of masonry dust. Bosch provides suit-

able vacuum cleaners.

Switch on the ma-

chine and place

the front part of

the cutting guide

on the workpiece.

Slide the machine

with moderate

feed, adapted to

the material to be

worked.

OBJ_BUCH-393-004.book Page 28 Monday, September 28, 2009 2:16 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PWS 750-125 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch PWS 750-125

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info