Bedienungsanleitung Bosch TA 211E (Seite 14 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

458026

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

TA 211 E

English

Timed se back

Operation

Automatic switching between normal and re-

duced operation according to the time switch

program.

Select this position when the thermal in-

sulation in your building is not so good and re-

duced heating operation is necessary (e. g., at

night) to prevent considerable cooling. During

reduced operation, the appliance remains in

operation with reduced temperature for any

outdoor temperature and the pump runs.

7.2.3 Continuous Normal

Operation

The flow temperature is not reduced.

Select this setting when you will be stay-

ing up late as an exception (e. g., party). In this

case, the setting on the time switch (accesso-

ry) for reduced operation is ignored. Do not

forget to switch back again later to automatic

switching operation .

7.3 Setting the Heating Curve

The heating curve determines the flow tem-

perature to which the appliance is limited,

based on the measured outside temperature.

With a correctly set heating curve, a constant

room temperature is maintained for any out-

door temperature.

The heating curve (Fig. ) of the TA 211 E re-

sults from a base point (c) and the maximum

feed temperature (e).

When commissioning, set flow temperature

control so that the dot is pointing to the right

(Fig. , e).

7.3.1 Base Point Adjustment (c)

The base point of the heating curve sets the

flow temperature (radiator temperature) in °C

when the outside temperature is +20 °C. It

can be set to values between 10 and 60 (°C).

The heating curve shown in Fig. is for a

base point of 25 °C. This setting of the base

point should be selected as a first starting

point.

In case your heating equipment permits,

select a lower setting value (e. g. 20). In case

the room temperature is too low with fully

opened thermostat valves, select a higher

value. (e. g. 30).

7.3.2Adjustment of

the Maximum Feed

Temperature (e)

On the flow tempera-

ture selector in the fa-

cia (e), the maximum heating flow tempera-

ture can be set between approx. 40 °C and

approx. 90 °C.

The maximum flow temperature selected here

is only reached with an outside temperature of

–15 °C (Fig. , Point e).

Note: The feed temperature selector (e) is

also the switch for summer operation

(, left end position).

Therefore, note the setting for the

average feed temperature (Fig. ,

Point e) for winter operation.

The required radiator temperature (flow tem-

perature) for an outdoor temperature of

–15 °C is contained in the design data of the

heating system. If this information is not avail-

able, values gained by experience must be

used.

If for very low outdoor temperatures and

completely open thermostat valves, it is too

cold in the rooms, select a setting value that is

a 1/2 scale division higher (Fig. , e). If for

very low outside temperature and fully opened

thermostatic valves, it is too warm in the

rooms, select a setting value that is a 1/2 scale

division lower (Fig. , e).

-40 -10

-30 -20

☞

Tip

☞

Tip

10 40

20 30

☞

Tip

ECO

☞

Tip

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch TA 211E Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info