Bedienungsanleitung Bosch TA 211E (Seite 15 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

458026

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

TA 211 E

English

7.3.3 Night Reduction (d)

In the position (frost protection), the heat-

ing unit remains switched off as long as the

outside temperature is above +4 °C. Burner

and pump are not in operation (see

Section 7.2).

The night reduction determines by how many

K (°C). The heating curve is shifted parallel

downward in reduced operation (the broken

line in Fig.

). Values between 0 and – 40 K

(°C) can be set.

Select a setting with which the desired

temperature reduction is achieved.

Note: A reduction of the flow temperature by

5 K (°C) results in approx. 1 K (°C)

room temperature reduction.

7.4 TA 211 E with Time Switch and TW 2

Remote Control (Accessory) (not in UK)

The TW 2 Remote Control is effective only

when the operating mode switch (b) of the

TA 211 E is in the position . If this is the

case, the operating mode can be set with the

operating mode switch on the remote control.

Set the base point for normal operation and

night reduction as described in Section 7.3.

In the position of the operating mode

switch on the TW 2 , a fixed reduction value

of 25 K (°C) is pre-programmed. The reduc-

tion value set on the adjustment knob of

the TA 211 E is not effective in this case.

Should the reduction value of 25 K (°C)

be too high or too low for longer absences, the

operating mode switch (b) of the TA 211 E

can be temporarily set to the position and

any desired reduction value selected on the

knob (d).

A detailed functional description can be found

in the operating instructions of the TW 2.

7.5 TA 211 E with TFQ 2 or TFP 3

Remote Control (Accessory) (not in UK)

The remote control is effective only when the

operating mode switch (b) of the TA 211 E is

either in the position . The operating mode

can then be set exclusively by means of the

operating mode switch on the remote control.

Note: The degree of flow temperature re-

duction is also set exclusively on

the TFQ 2/TFP 3.

A detailed functional description is provided

with the remote control.

8 Programming the time switch

(Accessory)

The TA 211 E is delivered without a time

switch.

For the operation of the time switch, refer to

the associated operating instructions.

9 General Notes

Heating units that can be operated with the

TA 211 E Regulator are equipped with an au-

tomatic device that limits the switching fre-

quency in two-point operation of the burner.

For more detailed information, refer to the in-

stallation instructions of the heating unit.

A frost protection circuit is also built into the

switching box of the heating unit that keeps

the flow temperature above +10 °C.

10 Malfunction

A malfunction of the regulator or a faulty con-

nection are indicated with an error code on the

control panel. The following error codes are

caused by the regulator TA 211 E:

• “AC” Contact failure or malfunction of the

regulator.

• “CC” Contact failure or defect external tem-

perature sensor.

-40 -10

-30 -20

☞

Tip

☞

Tip

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch TA 211E Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info