Bedienungsanleitung Bosch TR1100 - 18B (Seite 9 von 60) (Deutsch, Englisch, Polnisch)

697129

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Specifications

TR1100 – 6 720 876 016 (2018/04)

Electrical connection (Fig. 6)

• As a matter of principle, the water connections must be completed

first of all before the heater is connected to the electricity supply

(400 V AC, 3-phase). The appliance should be wired up according

to the circuit diagram on the inside of the cover.

• To guarantee compliance to relevant safety regulations, an all-pole

separator must be fitted during installation. The contact opening

must be at least 3 mm.

• Terminal BZ45Z20M (special accessories) can be used

if the connecting cable is fed into the heater via one of the bottom

holes 14a!

• The wires must not interfere with the operation of release button A

on the safety temperature limiter.

Installation note

• The installation of non plug-in ready appliances must be undertaken

by the respective utility operator or by a qualified specialist company,

who can also assist you when you are requesting the approval of

the utility company for installation of the appliance.

Mounting the cover onto the heater (Fig. 7)

• When you mount the cover onto the heater, ensure that the switch

knob and the switch spindle are correctly aligned.

Startup (Fig. 8)

The device is compliant to IEC 61000-3-12.

• Switch on via the water heater fuses in the domestic wiring.

• Select Setting "comfort" on the appliance and check the water

temperature.

At a low water-pipe pressure

• Turn on additional cold-water taps and check whether the heater

switches on. Remove the continuous-flow heater if the heater does

not switch on (Fig. A).

• Explain the appliance to the user and please give him the operating

instructions.

Priority switch for combination with electric storage heaters

(Fig. B)

If the heater is going to be operated in this way, a priority switch must

be connected into the line connecting the L2 phase to the appliance.

It should be mounted on the meter or distribution panel.

3 Specifications

* The pressure loss on the mixer must also be added.

Dimensions (Fig. 9)

a, b Control line for the electricity supply company connected

to the coil input on the charging contactor

f1 Safety temperature limiter with mains terminals

f3 Priority switch (current relay)

l1 Mains terminal (only on 21 kW and 24 kW appliances)

TR1100 18B TR1100 21 B TR1100 24 B

Rated power [kW] 18 21 24

Rated voltage 400 V 3 ~ 400 V 3 ~ 400 V 3 ~

Heating capacity – economy setting "eco" [kW]

1st stage

2nd stage

Heating capacity – intensive setting "comfort" [kW]

1st stage

2nd stage

10.5

Switch-on point [l/min]

1st stage

2nd stage

4.0

5.0

4.5

5.8

5.0

6.6

Mixed water [I/min] at rated power

approx. 38 °C

approx. 50 °C (supply temperature 12 °C)

9.8

6.7

11.5

7.8

13.1

9.0

Minimum flow pressure of appliance* [MPa (bar)]

with flow limiter

without flow limiter

0.6 (6)

0.4 (4) 0.8 (8)

0.5 (5)

0.9 (9)

0.6 (6)

Energy efficiency class B B B

Load profile SSS

Annual energy consumption [kWh] 495 497 501

Daily energy consumption [kWh] 2.301 2.313 2.337

Sound power level [dB] 15 15 15

Hot water heating energy efficiency [%] 37.2 37.1 36.8

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch TR1100 - 18B Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info