Bedienungsanleitung Bosch Uneo Maxx Systembox (Seite 15 von 219) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

766854

Zoom out

Zoom in

Vorherige Seite

1/219

Nächste Seite

English | 15

power tool and application tools, keeping their hands warm,

and organising workflows correctly.

Assembly

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

uBefore any work on the tool (e.g. maintenance, tool

change etc.) as well as during transport and storage,

set the rotational direction switch to the middle posi-

tion. There is risk of injury from unintentionally pressing

the on/off switch.

Battery Charging (see figure A)

uUse only the chargers listed in the technical data. Only

these chargers are matched to the lithium-ion battery of

your power tool.

Note: The battery is supplied partially charged. To ensure

full battery capacity, fully charge the battery in the charger

before using your power tool for the first time.

The lithium-ion battery can be charged at any time without

reducing its service life. Interrupting the charging process

does not damage the battery.

The lithium-ion battery is protected against deep discharge

by the "Electronic Cell Protection (ECP)". When the battery

is discharged, the power tool is switched off by means of a

protective circuit: The application tool no longer rotates.

uDo not continue to press the On/Off switch after the

power tool has automatically switched off. The battery

can be damaged.

– To remove the battery (10), press the release button

(18) and pull the battery to the rear and out of the power

tool. Do not use force to do this.

Follow the instructions on correct disposal.

Selecting drill chucks and tools

An SDS quick application tool is required for hammer

drilling.

To drill without impact in wood, metal, ceramic and plastic

you can use a suitable SDS quick application tool, a

hexagonal shank application tool or the keyless chuck with

application tools that do not have SDS quick.

For screwdriving, only use screwdriver bits which have a ball

catch (14) (DIN 3126-E6.3). Other screwdriver bits (13)

can be inserted using a universal bit holder with ball catch

(12).

You will find a selection of suitable application tools in the

accessories overview at the end of these operating instruc-

tions.

Changing the Keyless Chuck

You must use the keyless chuck (19) to work with applica-

tion tools that do not have SDS-Quick (e.g. cylindrical shank

drill bits).

Inserting the keyless chuck (seefigureB)

– Clean and lightly grease the insertion end of the shank.

– Insert the keyless chuck (19) with the shank into the tool

holder while turning it until it locks automatically.

– Check that it is locked by pulling the keyless chuck.

Removing the Keyless Chuck

– Push the locking sleeve (3) back and remove the keyless

chuck (19).

Changing the Tool

The tool holder can also accommodate dif-

ferent application tools with a hexagonal

shank with groove and SDS quick shank.

The tool holder allows for simple and con-

venient tool-free changing of the application

tool.

As a requirement of the system, the application tool can

move freely. This causes a certain radial run-out at no-load,

which has no effect on the accuracy of the drill hole, as the

drill bit centres itself upon drilling.

The dust protection cap (2) largely prevents the penetration

of drilling dust into the tool holder during operation. When

inserting the tool, make sure that the dust protection cap (2)

does not become damaged.

uReplace a damaged dust protection cap immediately.

It is recommended that you have use an after-sales

service for this.

Inserting SDS-Quick application tools (seefigureC)

– Clean and lightly grease the insertion end of the applica-

tion tool.

– Insert the application tool into the tool holder while turn-

ing it until it locks automatically.

– Check the latching by pulling the tool.

Removing SDS-Quick application tools (seefigureD)

– Push the locking sleeve (3) back and remove the applica-

tion tool.

Inserting application tools that do not have SDS-Quick

(seefigureE)

Note: Application tools that do not have SDS-Quick must not

be used for hammer drilling. Hammer drilling will damage

tools without SDS-Quick along with their chucks.

– Insert the keyless chuck (19).

– Hold the rear sleeve (21) of the keyless chuck (19) firmly

and turn the front sleeve (20) anti-clockwise until the tool

can be inserted. Insert the tool.

Bosch Power Tools 1 609 92A 6DK | (01.07.2021)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch Uneo Maxx Systembox Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info