Bedienungsanleitung Bosch Uneo Maxx Systembox (Seite 16 von 219) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

766854

Zoom out

Zoom in

Vorherige Seite

1/219

Nächste Seite

16 | English

– Hold the rear sleeve of the keyless chuck (19) and firmly

tighten the front sleeve by hand in a clockwise direction

until it stops clicking. This will automatically lock the drill

chuck.

– Check that it is seated securely by pulling the tool.

Note: If the tool holder was unscrewed all the way, a scrap-

ing sound may be heard while retightening the tool holder

and it may not fully tighten.

In this case, turn the front sleeve (20) anti-clockwise by one

turn. This will allow the tool holder to be fully tightened.

– Turn the "Drilling/hammer drilling" selector switch (4) to

the "drilling" position.

Removing application tools that do not have SDS-Quick

(seefigureF)

Hold the rear sleeve (21) of the keyless chuck firmly and

turn the front sleeve (20) of the keyless chuck anti-clock-

wise until the application tool can be removed.

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some

wood types, minerals and metal can be harmful to one’s

health. Touching or breathing-in the dust can cause allergic

reactions and/or lead to respiratory infections of the user or

bystanders.

Certain dust, such as oak or beech dust, is considered carci-

nogenic, especially in connection with wood-treatment ad-

ditives (chromate, wood preservative). Materials containing

asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the ma-

terials to be worked.

uAvoid dust accumulation at the workplace. Dust can

easily ignite.

Operation

Start-up

Inserting the Battery

uUse only original Bosch lithium-ion batteries with the

voltage stated on the type plate of your power tool.

Using other batteries can lead to injuries and pose a fire

hazard.

– Set the rotational direction switch (7) to the middle posi-

tion to avoid unintentionally switching it on. Insert the

charged battery (10) into the handle until you feel it en-

gage and it is flush with the handle.

Setting the Operating Mode

Use the "Drilling/hammer drilling" selector switch(4) to se-

lect the power tool's operating mode.

– To change the operating mode, press the release button

and slide the “Drilling/hammer drilling” selector

switch(4) to the required position.

Note: Only change the operating mode when the power tool

is switched off. Otherwise, the power tool may become dam-

aged.

– To change the operating mode, slide the “Drilling/hammer

drilling” selector switch (4) to the required position.

Position for hammer drilling into concrete

or stone

Position for drilling without impact in wood,

metal, ceramic and plastic and for screw-

driving

Setting the rotational direction (see figureG)

uOnly operate the rotational direction switch (7) when

the power tool is not in use.

The rotational direction switch (7) is used to change the ro-

tational direction of the power tool. However, this is not pos-

sible while the on/off switch (8) is being pressed.

–Right rotation: To drill and to drive in screws, press the

rotational direction switch (7) through to the left stop.

The rotational direction indicator for right rotation

(5) lights up when the on/off switch (8) is pressed

and the motor is running.

–Left rotation: To loosen and unscrew screws and nuts,

press the rotational direction switch (7) through to the

right stop.

The rotational direction indicator for left rotation

(6) lights up when the on/off switch (8) is pressed

and the motor is running.

Switching On/Off

– To start the power tool, press and hold the on/off switch

(8).

The lamp (11) lights up when the on/off switch (8) is lightly

or fully pressed, meaning that the work area is illuminated in

poor lighting conditions.

For low temperatures, the power tool reaches the full ham-

mer/impact capacity only after a certain time.

– To switch off the power tool, release the on/off switch

(8).

Adjusting the Speed/Impact Rate

– Adjust the speed/impact rate of the power tool when it is

on by pressing in the on/off switch(8) to varying extents.

Applying light pressure to the on/off switch(8) results in a

low rotational speed/impact rate. Applying increasing pres-

sure to the switch increases the speed/impact rate.

Run-out brake

Upon releasing the on/off switch (8), the drill chuck is

slowed down, which prevents the application tool from con-

tinuing to rotate.

When driving in screws, you should therefore only release

the on/off switch (8) once the screw has been inserted flush

1 609 92A 6DK | (01.07.2021) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch Uneo Maxx Systembox Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info