Bedienungsanleitung Bosch Universal Saw 18V 100 (Seite 19 von 257) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

766851

Zoom out

Zoom in

Vorherige Seite

1/257

Nächste Seite

English | 19

– Use a dust extraction system that is suitable for the ma-

terial wherever possible.

– Provide good ventilation at the workplace.

– It is advisable to wear a P2 filter class breathing mask.

The regulations on the material being machined that apply in

the country of use must be observed.

uAvoid dust accumulation at the workplace. Dust can

easily ignite.

Hood (see figuresGandH)

Fit the hood (9) before you connect the power tool to the

dust extraction system.

Position the hood (9) on the power tool so that the two outer

brackets engage in the recesses of the housing.

Remove the hood (9) when working without a dust extrac-

tion system and for mitre cuts. To do this, push the hood to-

gether at the level of the outer brackets and remove it by

pulling it forwards.

Connecting the dust extraction system (seefigureI)

Push the dust extraction adapter(22) (accessory) onto an

extraction hose(23) (accessory) until you hear it click into

place. Connect the dust extraction adapter(22) to the ex-

traction outlet(6) on the power tool and the extraction

hose(23) to a dust extractor (accessory).

You will find an overview of connecting to various dust ex-

tractors at the end of these operating instructions.

For optimum dust extraction, where possible use the anti-

splinter guard (20).

The dust extractor must be suitable for the material being

worked.

When extracting dry dust that is especially detrimental to

health or carcinogenic, use a special dust extractor.

Operation

Operating modes

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Pendulum action settings

The pendulum action can be adjusted using four different

settings, allowing the cutting speed, cutting capacity and the

cut itself to be optimally adapted to the material that you

want to cut.

You can also adjust the pendulum action during operation

using the adjusting lever (8).

No pendulum action

Low pendulum action

Moderate pendulum action

High pendulum action

The optimum pendulum level for each application can be de-

termined by a practical test. Note the following recommend-

ations:

– Select a lower pendulum level or switch off the pendulum

action completely if you wish to produce a finer or cleaner

cutting edge.

– Switch off the pendulum action when machining thin ma-

terials (e.g. sheets).

– Work on hard materials (e.g. steel) with low pendulum ac-

tion.

– You can work on soft materials and saw wood using max-

imum pendulum action.

Adjusting the mitre/bevel angle (seefigureJ)

The base plate (7) can be swivelled to the right or left to

make mitre cuts up to 45°.

The hood (9) and anti-splinter guard (20) cannot be used

while mitre cuts are being made.

– Remove the hood(9), the anti-splinter guard(20) and

the glide shoe(19).

– Pull the saw blade storage compartment(18) out of the

base plate(7).

– Loosen the screw(25) and push the base plate(7)

slightly towards the extraction outlet(6).

– The base plate has lock-in points at 0°, 22.5° and 45° on

the left and right so that the precise mitre/bevel angle can

be adjusted. Swivel the base plate(7) to the required po-

sition according to the scale(24). Other mitre/bevel

angles can be adjusted using a protractor.

– Then push the base plate(7) towards the saw blade(11)

as far as it will go.

– Retighten the screw(25).

Cut Control for mitre cuts (see figureK)

To enable you to track the cutting line (Cut Control), the

viewing window for CutControl (12) has a mark (26) for

right-angled cuts at 0° and a mark (27) for rightward- and

leftward-slanting mitre cuts at 45° according to the scale

(24).

The cut mark for mitre angles between 0° and 45° is propor-

tional. It can also be marked on the viewing window for

CutControl (12) using a non-permanent marker and easily

removed again.

We recommend making a test cut for precise results.

Moving the base plate (see figureJ)

You can move the base plate (7) back for sawing close to

edges.

Pull the saw blade storage compartment(18) out of the base

plate(7) or remove the glide shoe(19).

Loosen the screw (25) and push the base plate (7) towards

the extraction outlet (6) as far as it will go.

Retighten the screw (25).

Sawing with an offset base plate (7) is only possible with a

mitre angle of 0°. In addition, CutControl must not be used

with the base (10), the parallel guide with circle cutter (29)

(accessory) or the anti-splinter guard (20).

Bosch Power Tools 1 609 92A 5Y0 | (27.05.2021)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch Universal Saw 18V 100 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info