Bedienungsanleitung Bosch Universal Saw 18V 100 (Seite 20 von 257) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

766851

Zoom out

Zoom in

Vorherige Seite

1/257

Nächste Seite

20 | English

Starting Operation

Inserting the battery

Note: The use of batteries unsuitable for your power tool can

lead to malfunctions or damage to the power tool.

Insert the charged battery(4) into the battery receptacle un-

til you feel it engage and it is securely locked in place.

Switching on/off

To switch on the power tool, press the lock-off switch (1)

first. Then press the on/off switch (2) and keep it pressed.

The worklight lights up when the on/off switch (2) is lightly

or fully pressed allowing the work area to be illuminated in

poor lighting conditions.

To switch off the power tool, release the on/off switch (2).

Note: For safety reasons, the on/off switch (2) cannot be

locked; it must remain pressed during the entire operation.

Controlling the stroke rate

You can variably adjust the stroke rate of the power tool

when it is on by pressing in the on/off switch (2) to varying

extents.

Applying light pressure to the on/off switch (2) results in a

low stroke rate. Applying increasing pressure to the switch

increases the stroke rate.

The required stroke rate is dependent on the material and

the work conditions and can be determined using practical

tests.

It is recommended that you reduce the stroke rate when

placing the saw blade on the workpiece and when sawing

plastic and aluminium.

During prolonged periods of use at a low stroke rate, the

power tool may heat up significantly. Remove the saw blade

and let the power tool run at the maximum stroke rate for

around three minutes to cool down.

Temperature-dependent overload protection

In normal conditions of use, the power tool cannot be over-

loaded. If the power tool is overloaded or not kept within the

permitted battery temperature range, the speed is reduced

or the power tool switches off. At reduced speed, the power

tool will run again at full speed once the permitted battery

temperature is reached or the load is reduced. If it automat-

ically shuts down, switch the power tool off, allow the bat-

tery to cool down, then switch the power tool back on.

The three LEDs in the battery charge indicator (3) flash

quickly when the temperature of the battery is outside the

operating temperature range of −20 to +50°C and/or the

overload protection has been triggered.

Working Advice

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

uSwitch the power tool off immediately if the saw blade

becomes blocked.

uWhen machining small or thin workpieces, always use

a stable base or saw table (accessory).

Plunge cutting (see figureL)

uPlunge cuts may only be applied to soft materials,

such as wood, gypsum board, etc.

For plunge cutting, use only short saw blades. Plunge cutting

is possible only with a mitre angle of 0°.

Place the power tool so that the front edge of the base plate

(7) rests on the workpiece, without the saw blade (11)

touching the workpiece, and switch it on. On power tools

with stroke rate control, select the maximum stroke rate.

Press the power tool firmly against the workpiece and allow

the saw blade to plunge slowly into the workpiece.

As soon as the base plate (7) rests fully on the workpiece,

continue sawing along the required cutting line.

Parallel guide with circle cutter (accessory)

When working with the parallel guide with circle cutter (29)

(accessory), the workpiece must be no more than 30mm

thick.

Remove the base for CutControl (10) from the base plate

(7). To do this, push the base together gently and remove it

from the guide (21).

Parallel cuts (see figureM): Loosen the locking screw (28)

and slide the scale on the parallel guide through the guide

(21) in the base plate. Adjust the desired cutting width as a

scale value on the inside edge of the base plate. Retighten

the locking screw (28).

Circular cuts (see figureN): Drill a hole large enough to push

the saw blade through on the cutting line within the circle to

be cut. Machine the drill hole with a router or file so that the

saw blade can lie flush with the cutting line.

Position the locking screw (28) on the other side of the par-

allel guide. Slide the scale on the parallel guide through the

guide (21) into the base plate. Drill a hole in the workpiece

in the middle of the section to be cut out. Insert the centring

tip (30) through the inner opening of the parallel guide and

into the drilled hole. Adjust the radius as a scale value on the

inside edge of the base plate. Retighten the locking screw

(28).

Coolant/lubricant

As the material heats up along the cutting line when cutting

metal, you should apply coolant or lubricant.

Recommendations for Optimal Handling of the Battery

Protect the battery against moisture and water.

Only store the battery within a temperature range of −20 to

50°C. Do not leave the battery in your car in the summer, for

example.

Occasionally clean the ventilation slots on the battery using a

soft brush that is clean and dry.

A significantly reduced operating time after charging indic-

ates that the battery has deteriorated and must be replaced.

Follow the instructions on correct disposal.

1 609 92A 5Y0 | (27.05.2021) Bosch Power Tools

Bosch Universal Saw 18V 100 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info