Bedienungsanleitung Bosch UniversalChain 35 (Seite 17 von 343) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

708255

Zoom out

Zoom in

Vorherige Seite

1/343

Nächste Seite

English | 17

The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-

specific models.

Starting cycles generate brief voltage drops. Interference with other equipment/machines may occur in case of unfavourable

mains system conditions. Malfunctions are not to be expected for system impedances below 0.25ohm.

Noise/Vibration Information

3 600 HB8 1.0 3 600 HB8 1.1

Noise emission values determined according to EN60745-2-13.

Typically the A-weighted noise levels of the product are:

– Sound pressure level dB(A)

94 94

– Sound power level dB(A)

102 102

– Uncertainty K dB

2.0 2.0

Wear hearing protection!

Vibration total values ah (triax vector sum) and uncertainty K determined according to EN60745-2-13

– Vibration emission value a

m/s

4.0 4.0

– Uncertainty K m/s

1.5 1.5

The vibration level given in these instructions has been

measured in accordance with a standardised measuring pro-

cedure and may be used to compare power tools. It can also

be used for a preliminary estimation of exposure to vibra-

tion.

The stated vibration level applies to the main applications of

the power tool. However, if the power tool is used for differ-

ent applications, with different application tools or poorly

maintained, the vibration level may differ. This can signific-

antly increase the exposure to vibration over the total work-

ing period.

To estimate the exposure to vibration accurately, the times

when the tool is switched off or when it is running but not ac-

tually being used should also be taken into account. This can

significantly reduce the exposure to vibration over the total

working period.

Implement additional safety measures to protect the oper-

ator from the effects of vibration, such as servicing the

power tool and application tools, keeping the hands warm,

and organising workflows correctly.

Assembly

For Your Safety

u Warning! Switch off, remove plug from mains before

adjusting or cleaning. The same applies when the

mains cable is damaged, cut or entangled.

u Caution! Do not touch the rotating chain.

u Do not operate the chain saw near other people, chil-

dren or animals. Do not operate the chain saw after

drinking alcohol or under the influence of intoxicating

drugs or medication.

Electrical Safety

Your machine is double insulated for safety and requires no

earth connection. The operating voltage is 230VAC, 50Hz

(for non-EU countries 220V, 240V 50Hz) Contact your

Bosch Service Centre for details. If in doubt contact a quali-

fied electrician or the nearest Bosch Service Centre.

Only extension cables of design type H07RN-F or IEC

(60245 IEC66) are permitted for use.

When operating the chain saw with an extension cable, the

following conductor cross-sections are required:

– 1.0mm

: max. length 40m

– 1.5mm

: max. length 60m

– 2.5mm

: max. length 100m

It is recommended for increased electrical safety to use a Re-

sidual Current Device (RCD) with a tripping current of not

more than 30mA. Always check your RCD every time you

use it.

For products not sold in GB:

Warning: For your safety, it is required that the plug (16) at-

tached to the machine is connected with the extension cord

(17) as shown. The coupling of the extension cord must be

protected against splash water, be made of rubber or coated

with rubber. The extension cord must be used with a cable

strain relief.

The connection lead must be inspected for signs of damage

at regular intervals and may only be used if in perfect condi-

tion.

If the supply cable on the product is damaged, it must only

be replaced by a Bosch Service Centre. Only use approved

extension cables.

Products sold in GB only:

Your product is fitted with an BS 1363/A approved electric

plug with internal fuse (ASTA approved to BS 1362).

If the plug is not suitable for your socket outlets, it should be

cut off and an appropriate plug fitted in its place by an au-

thorised customer service agent. The replacement plug

should have the same fuse rating as the original plug.

Bosch Power Tools F 016 L81 829 | (28.11.2019)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch UniversalChain 35 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info