Bedienungsanleitung Bose B2 basmodule (Seite 38 von 146) (Englisch)

571290

Zoom out

Zoom in

Vorherige Seite

1/146

Nächste Seite

Cleaning glass

Dirt clings less easily to well-cleaned glass. Proceed

as follows:

1. Remove dust and loose soot with a dry cloth.

2. Clean the glass with stove window cleaner:

a. Apply stove window cleaner to a kitchen

sponge, rub down the entire glass surface and

give the cleaning agent time to react.

b. Remove the dirt with a moist cloth or kitchen

tissue.

3. Clean the glass again with a normal glass cleaning

product.

4. Rub the glass clean with a dry cloth or kitchen

tissue.

Do not use abrasive or aggressive products to

clean the glass.

Wear household gloves to protect your hands.

If the glass in the appliance is broken or

cracked, it must be replaced before you can

use the appliance again.

Make sure that no stove window cleaner runs

between the glass and the cast-iron door.

Maintaining enamelled fire

Never clean the appliance when it is still hot. The

enamelled surface of the fire can be cleaned most

effectively with a mild green soap and lukewarm

water. Use as little water as possible, rub the surface

dry and prevent the formation of rust. Wire wool or

other abrasives should never be used. Never place a

kettle directly onto an enamelled fire; use a stand and

prevent damage from occurring.

Lubrication

Although cast-iron is slightly self-lubricating, you will

still have to lubricate moving parts frequently.

Lubricate the moving parts (such as guide

systems,hinge pins, latches and air slides) with

heat resistant grease that is available in the

specialist trade.

Touching up damaged paint

Small areas of damaged paint finish can be touched

up with a spraying can of special heat-resistant paint

finish available from your supplier.

Touching up the enamelled surface

Enamelling is a process carried out by traditional

methods, meaning that it is possible that small colour

differences and damage may occur. The appliances

undergo a visual inspection in the factory, that is to

say, the inspector looks at the surface for a period of

10 seconds from a distance of 1 metre.

Any damage that does not stand out is regarded as

OK. A special heat-resistant paint is supplied along

with the apparatus, with which minor damage caused

during transport can be touched up.

Apply the heat-resistant paint in thin layers and leave

to dry well before using the appliance.

Checking the seal

Check whether the sealing rope of the door is still

in good condition and works well. The sealing rope

is subject to wear and needs to be replaced in time.

Check the appliance for air leaks. Close any

chinks with stove sealant.

Let the sealant harden fully before you start a

fire in the appliance, because otherwise any

moisture in the sealant will form bubbles in the

sealant and cause a new air leak.

Re-adjusting the locking cam

Check that the door is properly closed and adjust the

locking cam as necessary.

1. Slide the heat shield up and lift up the under side of

the heat shield from the positioning tabs on the

side wall of the appliance; see following figure.

Subject to change because of technicalimprovements

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bose B2 basmodule Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bose B2 basmodule

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info