Bedienungsanleitung Bostitch BF33 (Seite 16 von 300) (Alle Sprachen)

721876

Zoom out

Zoom in

Vorherige Seite

1/300

Nächste Seite

When the trigger lock-off is pressed to the left,

the tool will be fully operational. The trigger

lock-off should always be locked off whenever

any adjustments are made or when tool is not

in immediate use.

Non-mar Tip (ﬁ g. 1)

When using this tool on materials that you do

not want to mark, such as wood cladding, use

the plastic non-mar tip (m) over the contact

trip(c).

LED Indicator (ﬁ g. 1)

Your nailer is equipped with two LED indicator

lights (e) located on the back of the tool just below

the back cap. Also refer to to the Troubleshooting

Guide for further instruction.

LOW BATTERY

Replace battery with a

charged pack.

HOT PACK

Let the battery cool or

replace it with a cool pack.

JAM/STALL CONDITION

Rotate the stall release

lever to release. Refer to

Stall Release.

HOT TOOL

Let the tool cool down

before continuing use.

Stall Release (ﬁ g. 1, 3)

If the nailer is used in rigorous application where

all available energy in the motor is used to drive

a fastener, the tool may stall. The driver blade did

not complete the drive cycle and the jam/stall

indicator(e) will flash. Rotate the stall release lever

(f) on the tool and the mechanism will release.

If the driver blade does not automatically return

to the home position, proceed to Clearing a

Jammed Nail. If the unit continues to stall please

review the mode selection, material and fastener

length to be sure that it is not too rigorous an

application.

Clearing a Jammed Nail (ﬁ g. 1, 3)

If a nail becomes jammed in the nosepiece, the

jam/stall indicator light (e) will flash.

1. Remove battery pack from tool and engage

trigger safety lock-off (b).

2. Slide the spring-loaded pusher latch (h) to the

base of the magazine to lock it into place and

unload nail strip.

3. Using the hex tool (k) provided, loosen the

two hex bolts (q) at the top of the magazine.

4. Rotate the magazine (g) forward.

5. Remove jammed/bent nail, using pliers if

necessary.

6. If driver blade is in the down position, rotate

the stall release lever (f) on the top of the

nailer.

NOTE: If the driver blade will not reset after

rotating the stall release lever, manually

resetting the blade with a long screwdriver

may be necessary.

7. Rotate the magazine back into position under

the nose of the tool and tighten hex bolts (q).

8. Reinsert battery pack.

NOTE: The tool will disable itself and not reset

until the battery pack has been removed and

reinserted.

9. Reinsert nails into magazine (refer to Loading

the Tool).

10. Release the pusher latch (h).

11. Disengage the trigger safety lock-off (b) when

ready to continute nailing.

If nails become jammed in the nosepiece

frequently, have the tool serviced by an

authorised Bostitch service centre.

MAINTENANCE

Your Bostitch power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular

cleaning.

WARNING: To reduce the risk of

serious personal injury, turn tool

off and disconnect battery pack

before making any adjustments or

removing/installing attachments or

accessories. An accidental start-up can

cause injury.

The charger and battery pack are not serviceable.

There are no serviceable parts inside.

Lubrication

Your power tool requires no additional lubrication.

document do not constitute CE compliance for the products.

de ce document ne signifient en rien que les produits soient conformes aux normes CE.

Kopien dieses Dokuments erfüllen nicht die CE-Richtlinien für Produkte.

kopieën van dit document willen niet zeggen dat de producten voldoen aan de CE-vereisten.

udgør ikke CE overholdelse for produkterne.

kopiot eivät muodosta tuotteille CE-yhdenmukaisuutta.

εξουσιοδοτημένα αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για

τα προϊόντα.

documento non garantiscono la conformità CE per i relativi prodotti.

dokumentet oppfyller ikke kravene for CE-merking for produktet.

deste documento não estão em conformidade com a CE para os produtos.

documento no suponen la conformidad con las normas CE de los productos.

Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE

prezentowanych produktów.

CZ ©Stanley Bostitch. Niniejszy dokument nie może być kopiowany bez pozwolenia.

Nieautoryzowane kopie niniejszego dokumentu nie stanowią deklaracji zgodności CE

prezentowanych produktów.

SK ©Stanley Bostitch. Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto

dokumentu nie sú v súlade s CE pre dané výrobky.

HU ©Stanley Bostitch. A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül

sokszorosított dokumentum nem jelenti a termék CE-megfelelőségét.

Bostitch BF33 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info