Bedienungsanleitung Braun CT2s (Seite 13 von 66) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

514827

Zoom out

Zoom in

Vorherige Seite

1/66

Nächste Seite

• Carefully remove the lid from the cartridge.

• Slide the cartridge from the rear side into the base

of the station until it snaps into place.

• Slowly close the housing by pushing it down until it

locks.

• Using the special cord set (10), connect the

station power socket (13) to an electrical outlet.

Charging the shaver in the Clean&Charge station

Insert the shaver head down into the Clean&Charge

station.

Important: The shaver needs to be dry and free

from any foam or soap residue!

The contacts (7) on the back of the shaver need to

align with the contacts (15) in the Clean&Charge

station. Push the shaver in the correct position.

A beep sound confirms that the shaver sits properly

in the station. The Clean&Charge station will

automatically charge the shaver.

Cleaning the shaver

When the cleaning indicator lights up in the shaver

display, insert the shaver into the Clean&Charge

station, upside down and with the front showing.

Start automatic cleaning

Start the cleaning process by pressing the start

button (17). If the status light (16b) does not shine

(Clean&Charge station switches to stand-by after

about 10 minutes), press the start button twice.

Otherwise cleaning will not start.

For best shaving results, we recommend

cleaning after each shave.

The cleaning program consists of several cycles,

where cleaning fluid is flushed through the shaver

head. The cleaning time takes 3 minutes. During this

time the status light of the Clean&Charge station

blinks.

Leave the shaver in the station for drying. It takes

several hours until remaining moisture evaporates

depending on the climatic conditions. Afterwards

the shaver is ready for use.

After completing the cleaning and charging session,

the indicators of the Clean&Charge station turn off.

Removing the shaver from the Clean&Charge

station (see fig. F)

Hold the Clean&Charge station with one hand and

tilt the shaver slightly to the front to release it.

Cleaning Cartridge / Replacement (see fig. G)

When the level indicator lights up permanently

red, the remaining fluid in the cartridge is sufficient

for about 3 more cycles. When the level indicator

blinks red, the cartridge needs to be replaced

(about every 3–4 weeks when used daily).

After having pressed the lift button (14) to open the

housing, wait for a few seconds before removing

the used cartridge to avoid any dripping. Before

discarding the used cartridge, make sure to close

the openings using the lid of the new cartridge,

since the used cartridge will contain contaminated

cleaning solution.

The hygienic cleaning cartridge contains ethanol or

izopropanol (dependent on country – specification

see cartridge), which once opened will naturally

evaporate slowly into the surrounding air.

Each cartridge, if not used daily, should be replaced

after approximately 8 weeks to ensure optimal

disinfection.

The cleaning cartridge also contains lubricants, for

the shaving system which may leave residual marks

on the outer foil frame and the cleaning chamber

of the Clean&Charge station after cleaning. These

marks can be removed easily by wiping gently with a

damp cloth.

Accessories

Braun recommends changing your shaver’s

Foil & Cutter cassette every 18 months to maintain

your shaver’s maximum performance.

Available at your dealer or Braun Service Centres:

• Foil & Cutter cassette: 40S/40B

• Cleaning cartridge Clean&Charge: CCR

Environmental notice

This product contains rechargeable batteries.

In the interest of protecting the environment,

please do not dispose of the product in the

household waste at the end of its useful life.

Disposal can take place at a Braun Service Centre

or at appropriate collection points provided in your

country.

The cleaning cartridge can be disposed of with

regular household waste.

Subject to change without notice.

For electrical specifications, see printing on the

special cord set.

96189703_CoolTec_MN_S6-68.indd 1396189703_CoolTec_MN_S6-68.indd 13 11.10.12 10:4211.10.12 10:42

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Braun CT2s Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info